TDA8954TH datasheet(6/46 Pages) NXP

部件名	TDA8954TH

功能描述	2 횞 210 W class-D power amplifier

Download	46 Pages

Scroll/Zoom	100%

制造商	NXP [NXP Semiconductors]

网页	http://www.nxp.com

标志

6 / 46 page

TDA8954_1

Product data sheet

Rev. 01 — 24 December 2009

6 of 46

NXP Semiconductors

TDA8954

2

× 210 W class-D power amplifier

The TDA8954 single-chip Class D amplifier contains high-power switches, drivers, timing

and handshaking between the power switches, along with some control logic. To ensure

maximum system robustness, an advanced protection strategy has been implemented to

provide overvoltage, overtemperature and overcurrent protection.

Each of the two audio channels contains a PWM modulator, an analog feedback loop and

a differential input stage. The TDA8954 also contains circuits common to both channels

such as the oscillator, all reference sources, the mode interface and a digital timing

manager.

The two independent amplifier channels feature high output power, high efficiency, low

distortion and low quiescent currents. They can be connected in the following

configurations:

• Stereo Single-Ended (SE)

• Mono Bridge-Tied Load (BTL)

The amplifier system can be switched to one of three operating modes using pin MODE:

• Standby mode: featuring very low quiescent current

• Mute mode: the amplifier is operational but the audio signal at the output is

suppressed by disabling the voltage-to-current (VI) converter input stages

• Operating mode: the amplifier is fully operational, de-muted and can deliver an output

signal

A slowly rising voltage should be applied (e.g. via an RC network) to pin MODE to ensure

pop noise-free start-up. The bias-current setting of the (VI converter) input stages is

related to the voltage on the MODE pin.

In Mute mode, the bias-current setting of the VI converters is zero (VI converters are

disabled). In Operating mode, the bias current is at a maximum. The time constant

required to apply the DC output offset voltage gradually between Mute and Operating

mode levels can be generated using an RC network connected to pin MODE. An example

of a circuit for driving the MODE pin, optimized for optimal pop noise performance, is

shown in Figure 4. If the capacitor was omitted, the very short switching time constant

could result in audible pop noises being generated at start-up (depending on the DC

output offset voltage and loudspeaker used).

Fig 4.

Example of mode selection circuit

010aaa588

SGND

MODE

mute/

operating

10

μF

5.6 k

Ω

+5 V

470

Ω

standby/

operating

S2

S1

5.6 k

Ω

TDA8954

类似零件编号 - TDA8954TH

制造商	部件名	数据表	功能描述
NXP Semiconductors	TDA8954	439Kb / 46P	2 횞 210 W class-D power amplifier Rev. 01-24 December 2009
NXP Semiconductors	TDA8954	439Kb / 46P	2 횞 210 W class-D power amplifier Rev. 01-24 December 2009

More results

类似说明 - TDA8954TH

制造商	部件名	数据表	功能描述
NXP Semiconductors	TDA8953	756Kb / 46P	2 횞 210 W class-D power amplifier Rev. 01-24 December 2009
	TDA8954	439Kb / 46P	2 횞 210 W class-D power amplifier Rev. 01-24 December 2009
	TDA8920C	275Kb / 40P	2 X110 W class-D power amplifier Rev. 01-29 September 2008
Toshiba Semiconductor	TB2924FG	534Kb / 16P	Class D, 20 W 횞 2-channel (BTL) Low-Frequency Power Amplifier IC
Texas Instruments	TPA005D12	119Kb / 8P	[Old version datasheet] 2-W STEREO CLASS-D AUDIO POWER AMPLIFIER
NXP Semiconductors	TDA8922C	239Kb / 40P	2 X 75 W class-D power amplifier Rev. 01-7 September 2009
	TDA8920C	242Kb / 39P	2 X 110 W class-D power amplifier Rev. 02-11 June 2009
	TDA8920C	242Kb / 39P	2 쨈 110 W class-D power amplifier Rev. 02-11 June 2009
	TDA8950	271Kb / 39P	2 X 150 W class-D power amplifier Rev. 01-9 September 2008
	TDA8922B	201Kb / 32P	2 X 50 W class-D power amplifier Rev. 01-1 October 2004