MPC5646C Microcontroller

Description

The MPC5646C is a new family of next generation microcontrollers built on the Power Architecture embedded category. This document describes the features of the family and options available within the family members, and highlights important electrical and physical characteristics of the device.

The MPC5646C family expands the range of the MPC560xB microcontroller family. It provides the scalability needed to implement platform approaches and delivers the performance required by increasingly sophisticated software architectures. The advanced and cost-efficient host processor core of the MPC5646C automotive controller family complies with the Power Architecture embedded category, which is 100 percent user-modecompatible with the original Power Architecture user instruction set architecture (UISA). It operates at speeds of up to 120 MHz and offers high performance processing optimized for low power consumption. It also capitalizes on the available development infrastructure of current Power Architecture devices and is supported with software drivers, operating systems and configuration code to assist with users  implementations.

• e200z4d dual issue, 32-bit core Power Architecture compliant CPU

– Up to 120 MHz

– 4 KB, 2/4-Way Set Associative Instruction Cache

– Variable length encoding (VLE)

– Embedded floating-point (FPU) unit

– Supports Nexus3+

• e200z0h single issue, 32-bit core Power Architecture compliant CPU

– Up to 80 MHz

– Variable length encoding (VLE)

– Supports Nexus3+

• Up to 3 MB on-chip flash memory: flash page buffers to improve access time

• Up to 256 KB on-chip SRAM

• 64 KB on-chip data flash memory to support EEPROM emulation

• Up to 16 semaphores across all slave ports

• User selectable MBIST

• Low-power modes supported: STOP, HALT, STANDBY

• 16 region Memory Protection Unit (MPU)

• Dual-core Interrupt Controller (INTC). Interrupt sources can be routed to e200z4d, e200z0h, or both

• Frequency-Modulated Phase-Locked Loop (FMPLL)

• Crossbar switch architecture for concurrent access to peripherals, flash memory, and SRAM from multiple bus masters

• 32 channel eDMA controller with DMAMUX

• Timer supports input/output channels providing 16-bit input capture, output compare, and PWM functions(eMIOS)

• 2 analog-to-digital converters(ADC): one 10-bit and one 12-bit

• Cross Trigger Unit (CTU) to enable synchronization of ADC conversions with a timer event from the eMIOS or from the PIT

• Up to 8 serial peripheral interface (DSPI) modules

• Up to 10 serial communication interface (LINFlex) modules

• Up to 6 full CAN (FlexCAN) modules with 64 MBs each

• CAN Sampler to catch ID of CAN message

• 1 inter IC communication interface (I2C) module

• Up to 177 (LQFP) or 199 (BGA) configurable general purpose I/O pins

• System clocks sources

– 4–40 MHz external crystal oscillator

– 16 MHz internal RC oscillator

– FMPLL Additionally, there are two low power oscillators: 128 kHz internal RC oscillator, 32 kHz external crystal oscillator

• Real Time Counter (RTC) with clock source from internal

128 kHz or 16 MHz oscillators or external 4–40 MHz crystal

– Supports autonomous wake-up with 1 ms resolution with max timeout of 2 seconds

– Optional support from external 32 kHz crystal oscillator, supporting wake-up with 1 second resolution and max timeout of 1 hour

• 1 System Timer Module (STM) with four 32-bit compare channels

• Up to 8 periodic interrupt timers (PIT) with 32-bit counter resolution

• 1 Real Time Interrupt (RTI) with 32-bit counter resolution

• 1 Safety Enhanced Software Watchdog Timer (SWT) that supports keyed functionality

• 1 dual-channel FlexRay Controller with 128 message buffers

• 1 Fast Ethernet Controller (FEC)

• On-chip voltage regulator (VREG)

• Cryptographic Services Engine (CSE)

• Offered in the followingstandard package types:

–176-pin LQFP, 2424 mm, 0.5 mm Lead Pitch

–208-pin LQFP, 2828 mm, 0.5 mm Lead Pitch

– 256-ball MAPBGA, 1717mm, 1.0 mm Lead Pitch