SIP43101 datasheet(2/5 Pages) VISHAY

2 / 5 page

SiP43101

Vishay Siliconix

New Product

www.vishay.com

Document Number: 72640

S-32451, Rev. A—01-Dec-03

ABSOLUTE MAXIMUM RATINGS

VCC

35 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C1, E1, C2, E2

35 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C1-E1, C2-E2 (clamped by internal circuitry)

52 V

. . . . . . . . . . . . . . . . . . . . . .

Output Current

Continuous for one Output

200 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Peak for one Output

1.3 A

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

FAULT Output Current

10 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

FAULT Output Voltage

17.5 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

IN1, IN2A, IN2B

17.5 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage Temperature

−65 to 150_C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Junction Temperature

−55 to 125_C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Currents are positive into, negative out of the specificed terminal.

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation

of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating

conditions for extended periods may affect device reliability.

RECOMMENDED OPERATING RANGE

VCC

9 to 32 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating Temperature Range

−40 to 85_C

. . . . . . . . . . . . . . . . . . . . . . . . . . .

SPECIFICATIONS

Test Conditions Unless Specified

Limits

Parameter

Symbol

VCC = 25 V,IN1, IN2 = 0 V, IN1, IN2, INV2 = 5 V

CDEL = 10 nF, TA = TJ

Mina

Typb

Maxa

Unit

Power Supply

Supply Voltage

VCC

Supply Current

ICC

−40 to 85_C, Both Inputs Enabled

Logic Inputs (IN1, IN2A, IN2B)

Digital Input High Level

VIH

3.5

Digital Input Low Level

VIL

1.5

Input Bias Current, Low Level

IIL

IN1, IN2A, IN2B = 0 V

−0.40

Input Bias Current, High Level

IIH

IN1, IN2A, IN2B = 5 V

0.02

Switches 1&2 − High Side Configuration

Rise Time (Off to On)

RLOAD = 250 W to GND C1 C2 = 25 V

300

Rise Tiem (On to Off)

RLOAD = 250 W to GND, C1 , C2 = 25 V

300

Saturation Voltage

VSATHS

RLOAD = 125 W to GND

TA = 25 _C

1.3

Saturation Voltage

VSATHS

RLOAD = 125 W to GND

TA = −40 _C

1.5

Current Limit

ILIMHS

RLOAD = 0.25 W to GND, TA = 25 _C

1.1

Leakage Current

ILHS

E1, E2 = GND, C1 , C2 = 25 V,IN1, IN2A, IN2B = 0 V

Voltabe Clamp

VCLHS

Measure (VC1 − VE1) or (VC2 − VE2)

Switches 1&2 − Low Side Configuration

Rise Time (On to Off)

RLOAD = 250 W to VCC LOAD = 25 V to C1 C2

400

Rise Tiem (Off to On)

RLOAD = 250 W to VCC, LOAD = 25 V to C1 , C2

350

Saturation Voltage

VSATLS

RLOAD = 125 W to VCC

TA = 25 _C

1.3

Saturation Voltage

VSATLS

RLOAD = 125 W to VCC

TA = −40 _C

1.5

Current Limit

ILIMLS

RLOAD = 0.25 W to VCC, TA = 25 _C

1.1

Leakage Current

ILLS

E1, E2 = GND, C1 , C2 = 25 V,IN1, IN2A, IN2B = 0 V

Voltabe Clamp

VCLLS

Measure (VC1 − VE1) or (VC2 − VE2)

Turn-On Delay

CDEL Maximum Voltage

VDEL

4.7

CDEL Threshold

VDELTH

ICDEL

2.5

SIP43101 数据表(PDF) 2 Page - Vishay Siliconix

SIP43101 数据表(HTML) 2 Page - Vishay Siliconix

Html Pages

1 2 3 4 5

数据表下载

链接网址

SIP43101 数据表(PDF) 2 Page - Vishay Siliconix

SIP43101 数据表(HTML) 2 Page - Vishay Siliconix

Html Pages

1 2 3 4 5

数据表 下载

链接网址

数据表下载