OPB760 datasheet(4/7 Pages) TTELEC

4 / 7 page

General Note

TT Electronics reserves the right to make changes in product speciﬁcation without

notice or liability. All information is subject to TT Electronics’ own data and is

considered accurate at time of going to print.

Photologic® Reflective Object

Sensor

OPB760, OPB761, OPB762, OPB763 (Series N and T)

OPB770, OPB771, OPB772, OPB773 (Series NZ and TZ)

Issue C

05/2016

Page 4

OPTEK Technology, Inc.

1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200

www.optekinc.com | www.ttelectronics.com

Electrical Speciﬁcations

Absolute Maximum Ratings (TA=25°C unless otherwise noted)

Supply Voltage, VCC (not to exceed 3 seconds)

10 V

Storage Temperature Range

-40° C to +85° C

Operating Temperature Range

-40° C to +70° C

Lead Soldering Temperature (1/16” inch (1.6 mm) from case for 5 seconds with soldering iron)(1)

260° C

Input Diode Power Dissipation(2)

100 mW

Output Photologic® Power Dissipation(3)

200 mW

Total Device Power Dissipation(4)

300 mW

Voltage at Output Lead (Open Collector Output)

35 V

Diode Forward DC Current

40 mA

Diode Reverse DC Voltage

3 V

Electrical Characteristics (TA = 25°C unless otherwise noted)

SYMBOL

PARAMETER

MIN

TYP

MAX

UNITS

TEST CONDITIONS

Input Diode

Forward Voltage

1.8

IF = 40 mA, TA = 25° C

Reverse Current

100

μA

VR = 2.0 V, TA = 25° C

Output Photologic® Sensor

VCC

Operating DC Supply Voltage

4.75

5.25

ICCL

Low Level Supply Current:

Buffered Totem-Pole Output(5)(6)

Buffered Open-Collector Output(5)(6)

Vcc = 5.25 V, If = 0 mA (output open)

Inverted Totem-Pole Output(5)

Inverted Open-Collector Output(5)

Vcc = 5.25 V, If = 25 mA (output open)

ICCH

High Level Supply Current:

Buffered Totem-Pole Output(5)(6)

Buffered Open-Collector Output(5)

Vcc = 5.25 V, If = 25 mA (output open)

Inverted Totem-Pole Output(5)(6)

Inverted Open-Collector Output(5)(6)

Vcc = 5.25 V, If = 0 mA (output open)

IOH

High Level Output Current:

Buffered Open-Collector Output

100

μA

Vcc = 4.5 V, If = 25 mA, VOH = 30 V, TA=25°C

Inverted Open-Collector Output

100

μA

Vcc = 4.5 V, If = 0 mA, VOH = 30 V, TA = 25°C

Notes:

(1) RMA ﬂux is recommended. Duration can be extended to 10 seconds maximum when ﬂow soldering.

(2) Derate linearly 2.22 mW/°C above 25° C.

(3) Derate linearly 4.44 mW/°C above 25° C.

(4) Derate linearly 6.66 mW/°C above 25° C.Normal application would be with light source blocked, simulated by IF=0 mA.

(5) Tested at d = 0.080” (mm) from a 90% diffuse white test surface.

(6) Normal application would be with light source blocked, simulated by IF = 0 mA.

(7) All parameters tested using pulse technique.

OPB760 数据表(PDF) 4 Page - TT Electronics.

OPB760 数据表(HTML) 4 Page - TT Electronics.

Html Pages

1 2 3 4 5 6 7

数据表下载