| 数据搜索系统,热门电子元器件搜索 |
|
ACT2801 数据表(PDF) 13 Page - Active-Semi, Inc |
|
|
|||||||||||||||||||||||||||||
ACT2801 数据表(HTML) 13 Page - Active-Semi, Inc |
|
13 / 25 page ![]() Rev 9, 14-Mar-17 Innovative PowerTM - 13 - www.active-semi.com Copyright © 2015-2017 Active-Semi, Inc. ACT2801/ACT2801B/ACT2801C APPLICATIONS INFORMATION Battery Charge Termination Voltage Battery charge termination voltage is set by a resistor Rbtv connected from BTV pin to AGND as shown in Figure 5. The battery charge termination voltage is estimated as the following equation: Rbtv is selected based on the battery voltage rating. 1% accuracy resistor is recommended for Rbtv. LED Status Indication 4 LEDs ON/OFF and flash show the charge status and the remained capacity level as shown in the table 2. The LED status is based on battery voltage and operation modes. When battery voltage is low, LED1 is flashing. In charge mode, when a battery is fully charged, flashing stops and all the 4 LEDs are solid on. Battery level voltage shift (BLVS pin) LED1-4 voltage thresholds are adjusted from HZ mode during charging and discharging based on the compensated impedance. Those thresholds are programmed by a resistor connected from BLVS pin to AGND as shown in Figure 6. The following equation shows the LED4 voltage threshold: As long as LED4 is set, all the other 3 LED thresholds is fixed as shown in the table 3: Table 3: 4 LED Voltage Thresholds Input Current Limit An external resistor is used to set the input current limit connected from ILIM pin to AGND as shown in Figure 7. Input current limit has built-in soft startup and current foldback control loop. The input current limit is estimated as the following equation: RBLVS (ohm) 50K 60K 70K 80K LED1 3.35V 3.45V 3.55V 3.65V LED2 3.60V 3.70V 3.80V 3.90V LED3 3.75V 3.85V 3.95V 4.05V LED4 4.00V 4.10V 4.20V 4.30V VIN Input Rcs SW L Output Battery Cout CSP CSN BTV Rbtv Io Charge Mode (Boost or HZ Mode) ACT2801QL-T1028 / ACT2801CQL- T1028 :PB time > 30ms LED LED1 LED2 LED3 LED4 LED1 LED2 LED3 LED4 VBAT<2.9V Flash Off Off Off Off Off Off Off 2.9V≤VBAT<LED1 Flash Off Off Off Flash Off Off Off LED1≤VBAT<LED2 On Flash Off Off On Off Off Off LED2≤VBAT<LED3 On On Flash Off On On Off Off LED3≤VBAT<LED4 On On On Flash On On On Off VBAT≥LED4 On On On Flash On On On On VBAT≥LED4 (End of Charge) On On On On On On On On (2) ) k ( R ) mA ( 01 . 0 ) V ( 5 . 3 ) V ( V BLVS 4 BATLED (1) ) V ( 10 4 R ) V ( 1 . 4 ) V ( V 6 btv BAT Figure 5. Battery terminal voltage setting circuit VIN Input VOUT Rcs SW L Output Battery BAT Cout BLVS RBLVS Figure 6. Battery level voltage shift setting circuit ) (k R (V) 4 . 2 (A) I ILIM ILIM (3) Table2: LED Indication |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |