| 数据搜索系统,热门电子元器件搜索 |
|
MP3313GC 数据表(PDF) 18 Page - Monolithic Power Systems |
|
|
|||||||||||||||||||||||||||||
MP3313GC 数据表(HTML) 18 Page - Monolithic Power Systems |
|
18 / 26 page ![]() MP3313 – 3-CHANNEL, LINEAR/EXPONENTIAL DIMMING, WLED DRIVER W/ I2C MP3313 Rev.1.0 www.MonolithicPower.com 18 8/2/2017 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2017 MPS. All Rights Reserved. SLP_MD1:0 = 00: The short LED fault detection is disabled. SLP_MD1:0 = 01: The short LED fault detection is enabled, and the FT_SLP is set when the fault is detected. SLP_MD1:0 = 10: The short LED fault detection is enabled, the FT_SLP is set, and the string is marked off with the LEDx voltage that is higher than the threshold. SLP_MD1:0 = 11: FT_SLP is set, and the IC latch off when the fault is detected. Thermal Shutdown Protection To prevent the IC from operating at an exceedingly high temperature, thermal shutdown is implemented in the MP3313 by detecting the silicon die temperature. When the die temperature exceeds the upper threshold (TST), the IC shuts down and resumes normal operation when the die temperature drops below the lower threshold. Typically, the hysteresis value is 25°C. If OTP_SD = 0, the IC latches off when OTP is triggered. I2C Chip Address The 7-bit MSB device address is 0x36 - 0x37 selected by A0. If A0 is floating, it must be pulled up or down externally to set the address. After the start condition, the I2C-compatible master sends a 7-bit address followed by an eighth read (1) or write (0) bit. The following bit indicates the register address to or from which the data is written or read (see Figure 3). 0 A0 1 1 0 1 r/w 1 Figure 3: The I2C Compatible Device Address To avoid a glitch in the operation, the following bit changes only when the IC EN bit (0x10, bit[0]) or the three LED channel enable bits (0x10, bit[3:1]) are set to 0. The following bit should contain these bits: 1. Mapping mode bit (MAPMOD, 0x11, bit[7]) 2. Brightness mode bits (BRTMD2:0, 0x11, bit[6:4]) 3. Slope enable bit (SLPEN, 0x11, bit[3]) 4. Slope time bit (TSLP2:0, 0x11, bit[2:0]) 5. PWM sample rate bit (PWMSR1:0, 0x12, bit[7:6]) 6. PWM polarity bit (PWM_P, 0x12, bit[5]) 7. PWM hysteresis bit (HYS2:0, 0x12, bit [4:2]) 8. PWM filter bit (FILTER1:0, 0x12, bit[1:0]) 9. Auto frequency high threshold bit (FS_AUTOH7:0, 0x15, bit[7:0]) 10. Auto frequency low threshold bit (FS_AUTOL7:0, 0x16, bit[7:0]) |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |