EL7900ILCZ datasheet(2/8 Pages) RENESAS

2 / 8 page

EL7900

FN7377 Rev 8.00

Page 2 of 8

September 18, 2009

Absolute Maximum Ratings (TA = +25°C)

Thermal Information

Supply Voltage between VSD and GND . . . . . . . . . . . . . . . . . . . .6V

Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . . 6mA

ESD Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2kV

Operating Conditions

Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C

Thermal resistance (Typical, Note 1)

JA (°C/W)

ODFN Package . . . . . . . . . . . . . . . . . . . . . . . . . . . .

125

Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . +90°C

Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +100°C

Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . .see link below

http://www.intersil.com/pbfree/Pb-FreeReflow.asp

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and

result in failures not covered by warranty.

IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests

are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA

NOTE:

JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See

Tech Brief TB379

Electrical Specifications

VCC = 3V, TA = +25°C, unless otherwise specified.

PARAMETER

DESCRIPTION

CONDITION

MIN

TYP

MAX

UNIT

VDD

Power Supply Range

2.7

5.5

ICC1

Supply Current

RL = 1k, EV = 100lux

µA

EV = 0lux

µA

ICC2

Supply Current When Disabled

EN = VHI

0.5

µA

IL1

Light Current

EV = 100lux

62.5

µA

IL2

Light Current

EV = 10lux

6.2

µA

ILEAK

Dark Current

EV = 0lux

VO(MAX)

Maximum Output Compliance Voltage

at 95% of nominal output current, EV = 100lux

2.7

Rise Time (Note 2)

RL = 5k, EV = 300lux

105

µs

RL = 1k, EV = 1000lux

µs

Fall Time (Note 2)

RL = 5k, EV = 300lux

170

µs

RL = 1k, EV = 1000lux

µs

Delay Time for Rising Edge (Note 2)

RL = 5k, EV = 300lux

165

µs

RL = 1k, EV = 1000lux

112

µs

Delay Time for Falling Edge (Note 2)

RL = 5k, EV = 300lux

µs

RL = 1k, EV = 1000lux

µs

VLO

Maximum Voltage at EN Pin to Enable

0.6

VHI

Minimum Voltage at EN Pin to Disable

1.8

ILO

Input Current at EN Pin

VEN = 0V

0.01

µA

IHI

Input Current at EN Pin

VEN = 3V

µA

tEN

Enable Time

EV = 200lux

140

µs

tDIS

Disable Time

EV = 200lux

µs

NOTES:

2. Switching time measurement is based on Figures 1 and 2.

3. Fluorescent light is substituted by Green LED during production

EL7900ILCZ 数据表(PDF) 2 Page - Renesas Technology Corp

EL7900ILCZ 数据表(HTML) 2 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8

数据表下载

链接网址

EL7900ILCZ 数据表(PDF) 2 Page - Renesas Technology Corp

EL7900ILCZ 数据表(HTML) 2 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8

数据表 下载

链接网址

数据表下载