47

CAT.8100H

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

Specifications

Temperature Characteristics

(Max.Impedance Ratio)

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Tangent of loss angle (tan δ)

ESR ( 1)

Leakage Current ( 2)

Performance Characteristics

Item

–55 to +105°C

4 to 16V

22 to 560µF

± 20% at 120Hz, 20°C

Less than or equal to the specified value at 120Hz, 20°C

Less than or equal to the specified value at 100kHz, 20°C

Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C

Z+105°C / Z+20°C

1.25

(100kHz)

Z

–55°C / Z+20°C

1.25

Endurance

Damp Heat

(Steady State)

Resistance to

Soldering Heat

Marking

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 5000 hours at 105°C.

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 1000 hours at 60°C, 90% RH.

After soldering the capacitor under the soldering conditions

prescribed here, the capacitor shall meet the specifications listed at

right.

Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.

The duration for over +230°C temperature at capacitor surface shall

not exceed 60 seconds.

In case peak temperature is 250°C or less, reflow soldering shall be

two times maximum.

In case peak temperature is 260°C or less, reflow soldering shall be

once.

Measurement for solder temperature profile shall be made at the

capacitor top and the terminal.

Navy blue print on the case top

Capacitance change

tan δ

Leakage current ( 2)

Within ± 20% of the initial capacitance value ( 3)

150% or less than the initial specified value

150% or less than the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current ( 2)

Within ± 20% of the initial capacitance value ( 3)

150% or less than the initial specified value

150% or less than the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current ( 2)

Within ± 10% of the initial capacitance value ( 3)

130% or less than the initial specified value

130% or less than the initial specified value

Less than or equal to the initial specified value

Load life of 5000 hours at 105°C.

SMD type : Lead free reflow soldering condition at

260°C peak correspondence.

Compliant to the RoHS directive (2011/65/EU).

AEC-Q200 compliant. Please contact us for details.

1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120

minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

P

1

C

2

S

3

0

4

J

5

2

6

2

7

1

8

M

9

C

10

L

11

1

12

G

13

S

14

Configuration

Taping code

Size code

Capacitance tolerance (±20%)

Rated capacitance (220µF)

Rated voltage (6.3V)

Series name

Type

H

0.3 MAX.

C±0.2

L

Series

Voltage ( j:6.3v)

Plastic platform

Lot No.

Capacitance

Negative

Positive

+0.1

-0.4

Dimensions

Type numbering system (Example : 6.3V 220µF)

Voltage

V

4

6.3

10

16

Code

g

j

A

C

Size

φD

L

A

B

C

E

H

φ5

5.0

5.9

6.0

5.3

5.3

1.6

0.5 to 0.8

φ6.3

6.3

5.9

7.3

6.6

6.6

2.1

0.5 to 0.8

φ8

8.0

6.9

9.0

8.3

8.3

3.2

0.8 to 1.1

(mm)

Dimension table in next page.

PCS

Long Life

PCF

Frequency coefficient of rated ripple current

Coefficient

120Hz 1kHz 10kHz 100kHz or more

0.05

0.30

0.70

1.00