66

CAT.8100H

PLX

Specifications

Temperature Characteristics

(Max.Impedance Ratio)

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Tangent of loss angle (tan δ)

ESR ( 1)

Leakage Current ( 2)

Performance Characteristics

Item

–55 to +125°C

16 to 50V

22 to 390µF

± 20% at 120Hz, 20°C

Less than or equal to the specified value at 120Hz, 20°C

Less than or equal to the specified value at 100kHz, 20°C

Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C

Z+125°C / Z+20°C

1.25

(100kHz)

Z

–55°C / Z+20°C

1.25

Endurance

Damp Heat

(Steady State)

Resistance to

Soldering Heat

Marking

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 3000 hours at 125°C.

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 1000 hours at 60°C, 90% RH.

After soldering the capacitor under the soldering conditions

prescribed here as preheat at 150 to 200°C for 60 to 180 seconds

and peak temperature at 265°C for 10 seconds or less, the

capacitor shall meet the specifications listed at right, provided that

its temperature profile is measured at both of terminal ends facing

the soldering side.

Navy blue print on the case top

Capacitance change

tan δ

Leakage current ( 2)

ESR ( 1)

Within ± 20% of initial value ( 3)

150% or less of the initial specified value

150% or less of the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current ( 2)

ESR ( 1)

Within ± 20% of initial value ( 3)

150% or less of the initial specified value

150% or less of the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current ( 2)

ESR ( 1)

Within ± 10% of the initial capacitance value ( 3)

130% or less than the initial specified value

130% or less than the initial specified value

Less than or equal to the initial specified value

High reliability, High voltage (to 50V).

Low ESR, High ripple current.

Long life of 3000 hours at 125°C.

Radial lead type:

Lead free flow soldering condition correspondence.

Compliant to the RoHS directive (2011/65/EU).

AEC-Q200 compliant. Please contact us for details.

1 ESR should be measured at both of the terminal ends closest to the capacitor body.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120

minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

P

1

L

2

X

3

1

4

V

5

3

6

9

7

0

8

M

9

10 11

Capacitance tolerance (±20%)

Rated capacitance (39µF)

Rated voltage (35V)

C L

12

1

Size code

Series name

Type

Configuration

L+0.5MAX.

15MIN

4MIN

Resin coated Case

φd

Capacitance

Series

Lot. No.

Voltage(V:35V)

Dimensions

Radial Lead Type, Long Life Assurance

Dimension table in next page.

Voltage

V

16

20

25

35

50

Code

C

D

E

V

H

Size

φD

L

P

φd

φ10

10.0

12.5

5.0

0.6

φ8

8.0

8.5

3.5

0.6

φ8

8.0

11.5

3.5

0.6

(mm)

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

Please refer to page 20 about the end seal configuration.

PLX

Higher

Temperature

PLV

Frequency coefficient of rated ripple current

Coefficient

120Hz 1kHz 10kHz 100kHz or more

0.05

0.30

0.70

1.00