45

CAT.8100H

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

Specifications

Temperature Characteristics

(Max.Impedance Ratio)

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Tangent of loss angle (tan δ)

ESR ( 1)

Leakage Current ( 2)

Performance Characteristics

Item

–55 to +105°C

2.5 to 16V

47 to 4700µF

± 20% at 120Hz, 20°C

Less than or equal to the specified value at 120Hz, 20°C

Less than or equal to the specified value at 100kHz, 20°C

Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C

Z+105°C / Z+20°C

1.25

(100kHz)

Z

–55°C / Z+20°C

1.25

Endurance

Damp Heat

(Steady State)

Resistance to

Soldering Heat

Marking

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 2000 hours at 105°C.

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 1000 hours at 60°C, 90% RH.

After soldering the capacitor under the soldering conditions

prescribed here, the capacitor shall meet the specifications listed at

right.

Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.

The duration for over +230°C temperature at capacitor surface shall

not exceed 60 seconds.

In case peak temperature is 250°C or less, reflow soldering shall be

two times maximum.

In case peak temperature is 260°C or less, reflow soldering shall be

once.

Measurement for solder temperature profile shall be made at the

capacitor top and the terminal.

Navy blue print on the case top

Capacitance change

tan δ

Leakage current ( 2)

Within ± 20% of the initial capacitance value ( 3)

150% or less than the initial specified value

150% or less than the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current ( 2)

Within ± 20% of the initial capacitance value ( 3)

150% or less than the initial specified value

150% or less than the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current ( 2)

Within ± 10% of the initial capacitance value ( 3)

130% or less than the initial specified value

130% or less than the initial specified value

Less than or equal to the initial specified value

Higher Capacitance, Low ESR, High ripple current.

Load life of 2000 hours at 105°C.

SMD type : Lead free reflow soldering condition at

260°C peak correspondence.

Compliant to the RoHS directive (2011/65/EU).

AEC-Q200 compliant. Please contact us for details.

1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120

minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

P

1

C

2

G

3

0

4

J

5

4

6

7

7

1

8

M

9

C

10

L

11

1

12

G

13

S

14

Configuration

Taping code

Capacitance tolerance (±20%)

Rated capacitance (470µF)

Rated voltage (6.3V)

Series name

Type

H

0.3 MAX.

C±0.2

L

Series

Voltage ( j:6.3v)

Plastic platform

Lot No.

Capacitance

Negative

Positive

+0.1

-0.4

Dimensions

Type numbering system (Example : 6.3V 470µF)

Dimension table in next page.

PCG

PCF

Higher

Capacitance

Voltage

V

2.5

4

6.3

10

16

Code

e

g

j

A

C

Size

φD

L

A

B

C

E

H

φ5

5.0

5.9

6.0

5.3

5.3

1.6

0.5 to 0.8

φ6.3

6.3

5.9

7.3

6.6

6.6

2.1

0.5 to 0.8

φ8

8.0

6.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ10

10.0

7.9

11.0

10.3

10.3

4.6

0.8 to 1.1

φ10

10.0

9.9

11.0

10.3

10.3

4.6

0.8 to 1.1

φ10

10.0

12.6

11.0

10.3

10.3

4.6

0.8 to 1.1

(mm)

Frequency coefficient of rated ripple current

Coefficient

120Hz 1kHz 10kHz 100kHz or more

0.05

0.30

0.70

1.00