2

Technical Data

4337

Effective April 2016

FP1005R

High frequency, high current power inductors

www.eaton.com/elx

Product Specifications

(nH) ±10%

(nH) minimum

(A)

(A)

(A)

DCR (mΩ)

@ 20°C

R1 Version

FP1005R1-R08-R

85

61

53

90

64

0.39 ±7.7%

536

FP1005R1-R10-R

100

72

53

73

57

0.39 ±7.7%

536

FP1005R1-R12-R

120

86

53

60

48

0.39 ±7.7%

536

FP1005R1-R15-R

150

108

53

47

37

0.39 ±7.7%

536

FP1005R1-R22-R

220

158

53

33

26

0.39 ±7.7%

536

R2 Version

FP1005R2-R08-R

85

61

50

90

64

0.47 ±6.7%

536

FP1005R2-R10-R

100

72

50

73

57

0.47 ±6.7%

536

FP1005R2-R12-R

120

86

50

60

48

0.47 ±6.7%

536

FP1005R2-R15-R

150

108

50

47

37

0.47 ±6.7%

536

FP1005R2-R22-R

220

158

50

33

26

0.47 ±6.7%

536

R3 Version

FP1005R3-R08-R

85

61

45

90

64

0.55 ±5.4%

536

FP1005R3-R10-R

100

72

45

73

57

0.55 ±5.4%

536

FP1005R3-R12-R

120

86

45

60

48

0.55 ±5.4%

536

FP1005R3-R15-R

150

108

45

47

37

0.55 ±5.4%

536

FP1005R3-R22-R

220

158

45

33

26

0.55 ±5.4%

536

R4 Version

FP1005R4-R12-R

120

86

45

60

48

0.70 ±10%

536

1. Open Circuit Inductance (OCL) Test Parameters: 100 kHz, 0.1 Vrms, 0.0 Adc, +25 °C

2. Full Load Inductance (FLL) Test Parameters: 100 kHz, 0.1 Vrms, Isat1, +25 °C

PCB layout, trace thickness and width, air-flow, and proximity of other heat generating components will affect the

temperature rise. It is recommended that the temperature of the part not exceed 125 °C under worst case operating

conditions verified in the end application.

4. I

5. I

table), L: (Inductance in nH), Symbol I (Peak to peak ripple current in Amps).

7. Part Number Definition: FP1005Rx-Rxx-R

FP1005R= Product code and size

x= Version indicator

-Rxx= Inductance value in μH, R= decimal point

-R suffix = RoHS compliant

Part marking: FPT1005Rx = (x=version indicator), Rxx=inductance value in uH, (R=decimal point)

wwllyy=date code, R=revision level.

Tolerances are ±0.25 millimeters unless stated otherwise.

All soldering surfaces must be coplanar within 0.1016 millimeters.

PCB tolerances are ±0.1 millimeters unless stated otherwise.

DCR is measured from point “a” to point “b.”

Do not route traces or vias underneath the inductor.

Dimensions (mm)