2

Technical Data

4341

Effective October 2015

FP1007

High frequency, high current power inductors

www.eaton.com/elx

Product specifications

(nH)±10%

(nH) minimum

I

rms

3

(amps)

I

4

(amps)

I

5

(amps)

DCR (mΩ)

@ 20°C ±5%

R1 version

FP1007R1-R12-R

120

86

60

81

65

0.29 ± 10%

371

FP1007R1-R14-R

140

100

60

72

56

0.29 ± 10%

371

FP1007R1-R17-R

170

122

60

58

46

0.29 ± 10%

371

FP1007R1-R22-R

215

155

60

50

36

0.29 ± 10%

371

FP1007R1-R30-R

300

216

60

32

26

0.29 ± 10%

371

R2 version

FP1007R2-R12-R

120

86

51

81

65

0.48 ± 8%

368

FP1007R2-R14-R

140

100

51

72

56

0.48 ± 8%

368

FP1007R2-R17-R

170

122

51

58

46

0.48 ± 8%

368

FP1007R2-R22-R

215

155

51

50

36

0.48 ± 8%

368

FP1007R2-R30-R

300

216

51

32

26

0.48 ± 8%

368

R3 version

FP1007R3-R12-R

115

83

61

94

86

0.29 ± 5%

354

FP1007R3-R15-R

150

108

61

76

70

0.29 ± 5%

354

FP1007R3-R17-R

175

126

61

66

60

0.29 ± 5%

354

FP1007R3-R22-R

215

155

61

50

43

0.29 ± 5%

354

FP1007R3-R23-R

230

165

61

48

40

0.29 ± 5%

354

FP1007R3-R27-R

270

194

61

40

34

0.29 ± 5%

354

FP1007R3-R30-R

300

216

61

35

30

0.29 ± 5%

354

1. Open Circuit Inductance (OCL) Test Parameters: 100kHz, 0.1Vrms, 0.0Adc, +25°C

2. Full Load Inductance (FLL) Test Parameters: 100kHz, 0.1Vrms, I

3. I

necessary for AC currents. PCB layout, trace thickness and width, air-flow, and proximity of other

heat generating components will affect the temperature rise. It is recommended that the

temperature of the part not exceed 125°C under worst case operating conditions verified in the

end application.

4. I

5. I

6. K-factor: Used to determine B

B

-3

. B

L: (Inductance in nH), ∆I (Peak-to-peak ripple current in Amps).

7. Part Number Definition: FP1007Rx-Rxx-R

FP1007R= Product code and size

x = DCR indicator

Rxx = Inductance value in μH, R= decimal point

-R suffix = RoHS compliant

Dimensions (mm)

Part marking: FP1007Rx (x = DCR indicator), Rxx (xx = inductance value in

uH, R = decimal point, wwllyy = date code, R = revision level

Tolerances are ±0.25 millimeters unless stated otherwise.

PCB tolerances are ±0.1 millimeters unless stated otherwise

All soldering surfaces to be coplanar within 0.1 millimeter

DCR measured from point “a” to point “b”

Do not route traces or vias underneath the inductor

Recommended Pad Layout

Schematic