FP1008R5-R150-R datasheet(2/7 Pages) EATON

2 / 7 page

Technical Data

10520

Effective April 2017

FP1008R5 and FP1008R6

High frequency, high current power inductors

www.eaton.com/electronics

Product specifications

Part Number8

OCL1

(nH) ±10%

FLL2

(nH) minimum

rms

(A)

sat1

(A)

sat2

(A)

sat3

(A)

DCR (mΩ)

±5% @ 20 °C

K-factor7

R5 version

FP1008R5-R120-R

120

103

0.170

342

FP1008R5-R150-R

150

108

0.170

342

FP1008R5-R180-R

180

130

0.170

342

FP1008R5-R220-R

220

158

0.170

342

FP1008R5-R270-R

270

194

0.170

342

FP1008R5-R300-R

300

216

0.170

342

R6 version

FP1008R6-R100-R

100

103

0.180

342

FP1008R6-R120-R

120

103

0.180

342

FP1008R6-R150-R

150

108

0.180

342

FP1008R6-R180-R

180

130

0.180

342

FP1008R6-R220-R

220

158

0.180

342

FP1008R6-R270-R

270

194

0.180

342

FP1008R6-R300-R

300

216

0.180

342

1. Open Circuit Inductance (OCL) Test Parameters: 100 kHz, 0.1 Vrms, 0.0 Adc, +25 °C

2. Full Load Inductance (FLL) Test Parameters: 100 kHz, 0.1 V

rms, Isat1, +25 °C

3. I

rms: DC current for an approximate temperature rise of 40 °C without core loss. Derating is

necessary for AC currents. PCB layout, trace thickness and width, air-flow, and proximity of

other heat generating components will affect the temperature rise. It is recommended that the

temperature of the part not exceed 125 °C under worst case operating conditions verified in the

end application.

4. I

sat1: Peak current for approximately 20% rolloff @ +25 °C

5. I

sat2: Peak current for approximately 20% rolloff @ +100 °C

6. I

sat3: Peak current for approximately 20% rolloff @ +125 °C

7. K-factor: Used to determine B

p-p for core loss (see graph).

p-p = K * L * ∆I * 10

-3

. B

p-p:(Gauss), K: (K-factor from table), L:

(Inductance in nH), ∆I (Peak to peak ripple current in Amps).

8. Part Number Definition: FP1008Rx-Rxxx-R

FP1008R= Product code and size

x= Version indicator

-Rxxx= Inductance value in uH, R= decimal point

-R suffix = RoHS compliant

Dimensions (mm)

Part marking: FP1008Rx (x = Version), Rxxx= Inductance value in uH (R= decimal point) xxxx = Lot code

Tolerances are ±0.15 millimeters unless stated otherwise

Pad layout tolerances are ±0.1 millimeters unless stated otherwise

All soldering surfaces to be coplanar within 0.1 millimeter

DCR measured from point “A” to point “B”

Do not route traces or vias underneath the inductor

FP1008R5-R150-R 数据表(PDF) 2 Page - Eaton All Rights Reserved.

FP1008R5-R150-R 数据表(HTML) 2 Page - Eaton All Rights Reserved.

Html Pages

1 2 3 4 5 6 7

数据表下载

链接网址

FP1008R5-R150-R 数据表(PDF) 2 Page - Eaton All Rights Reserved.

FP1008R5-R150-R 数据表(HTML) 2 Page - Eaton All Rights Reserved.

Html Pages

1 2 3 4 5 6 7

数据表 下载

链接网址

数据表下载