FP1008R2-R150-R datasheet(2/6 Pages) EATON

2 / 6 page

Technical Data

10408

Effective June 2015

FP1008R1 and FP1008R2

High frequency, high current power inductors

www.eaton.com/elx

Product specifications

Part Number9

OCL1

(nH)±10%

FLL2

(nH) minimum

rms

(amps)

sat1

(amps)

sat2

(amps)

sat3

(amps)

DCR (mΩ)

±5% @ 20°C

K-factor7

R1 version

FP1008R1-R120-R

120

112

0.17

342

FP1008R1-R150-R

150

108

0.17

342

FP1008R1-R180-R

180

130

0.17

342

FP1008R1-R220-R

220

158

0.17

342

FP1008R1-R270-R

270

194

0.17

342

FP1008R1-R300-R

300

216

0.17

342

R2 version

FP1008R2-R120-R

120

112

0.18

342

FP1008R2-R150-R

150

108

0.18

342

FP1008R2-R180-R

180

130

0.18

342

FP1008R2-R220-R

220

158

0.18

342

FP1008R2-R270-R

270

194

0.18

342

FP1008R2-R300-R

300

216

0.18

342

1. Open Circuit Inductance (OCL) Test Parameters: 100kHz, 0.1V

rms, 0.0Adc, +25°C

2. Full Load Inductance (FLL) Test Parameters: 100kHz, 0.1V

rms, Isat1, +25°C

3. I

rms: DC current for an approximate temperature rise of 40ºC without core loss. Derating is necessary

for AC currents. PCB layout, trace thickness and width, air-flow, and proximity of other heat generating

components will affect the temperature rise. It is recommended that the temperature of the part

not exceed 125°C under worst case operating conditions verified in the end application.

4. I

sat1: Peak current for approximately 20% rolloff @ +25ºC

5. I

sat2: Peak current for approximately 20% rolloff @ +100ºC

6. I

sat3: Peak current for approximately 20% rolloff @ +125ºC

7. K-factor: Used to determine B

p-p for core loss (see graph).

p-p = K * L * ∆I * 10

-3

. B

p-p:(Gauss), K: (K-factor from table),

L: (Inductance in nH), ∆I (Peak-to-peak ripple current in Amps).

8. Part Number Definition: FP1008Rx-Rxxx-R

FP1008 R= Product code and size

x = DCR indicator

Rxxx = Inductance value in μH, R = decimal point

- R suffix = RoHS compliant

Dimensions (mm)

Part marking: FP1008Rx (x= DCR indicator), Rxxx (xxx=inductance value in uH, R=decimal point),

wwllyy = date code, R = revision level

Tolerances are ±0.15 millimeters unless stated otherwise

PCB tolerances are ±0.1 millimeters unless stated otherwise

All soldering surfaces to be coplanar within 0.1 millimeter

DCR measured from point “a” to point “b”

Do not route traces or vias underneath the inductor

Recommended Pad Layout

Schematic

3.0

5.0

2.5

3.56

4.06

2.5

8.0

max

0.2

min

10.8

max

8.0

max

FP1008Rx

Rxxx

wwllyy R

FP1008R2-R150-R 数据表(PDF) 2 Page - Eaton All Rights Reserved.

FP1008R2-R150-R 数据表(HTML) 2 Page - Eaton All Rights Reserved.

Html Pages

1 2 3 4 5 6

数据表下载

链接网址

FP1008R2-R150-R 数据表(PDF) 2 Page - Eaton All Rights Reserved.

FP1008R2-R150-R 数据表(HTML) 2 Page - Eaton All Rights Reserved.

Html Pages

1 2 3 4 5 6

数据表 下载

链接网址

数据表下载