HCM1103-2R2-R datasheet(2/7 Pages) EATON

2 / 7 page

Technical Data

4449

Effective July 2017

HCM1103

High current power inductors

www.eaton.com/electronics

Product Specifications

Dimensions (mm)

Part

OCL1

FLL min.2

Irms3

Isat4 @

+25 °C

Number6

±20% (µH)

(µH)

(A)

DCR (mΩ) @

+20 °C Typical

DCR (mΩ) @

+20 °C Maximum

K-Factor5

HCM1103-R12-R

0.12

0.07

0.55

0.61

1200

HCM1103-R36-R

0.36

0.26

1.10

1.30

711

HCM1103-R47-R

0.47

0.33

1.50

2.00

515

HCM1103-R68-R

0.68

0.38

2.90

3.40

510

HCM1103-1R0-R

1.0

0.56

5.50

6.00

377

HCM1103-2R2-R

2.2

1.2

8.40

9.00

264

HCM1103-3R3-R

3.3

1.9

9.0

14.5

16.0

230

HCM1103-4R7-R

4.7

2.6

7.0

20.5

22.5

205

HCM1103-8R2-R

8.2

4.6

5.0

8.5

35.0

38.5

153

HCM1103-100-R

10.0

5.6

5.0

7.5

40.0

44.0

141

HCM1103-150-R

15.0

8.4

4.0

6.0

59.0

65.0

114

HCM1103-220-R

22.0

12.3

3.0

5.0

90.0

99.0

1. Open Circuit Inductance (OCL) Test Parameters: 100 kHz, 0.25 Vrms, 0.0 Adc @

+25 °C

2. Full Load Inductance (FLL) Test Parameters: 100 kHz, 0.25 Vrms, Isat @ +25 °C.

3. Irms: DC current for an approximate temperature rise of 40 °C without core

loss. Derating is necessary for AC currents. PCB layout, trace thickness and

width, air-flow and proximity of other heat generating components will affect

the temperature rise. It is recommended that the temperature of the part not

exceed

+125 °C under worst case operating conditions verified in the end

application.

4. Isat: Peak current for approximately 30% rolloff at +25 °C

5. K-factor: Used to determine Bp-p for core loss (see graph). Bp-p

= K * L * ∆I. Bp-p:(Gauss), K: (K-factor from table),

L: (Inductance in µH), ∆I (peak-to-peak ripple current in Amps).

6. Part Number Definition: HCM1103-xxx-R

HCM1103 = Product code and size

xxx= Inductance value in µH, R = decimal point,

if no R is present then third character = number of zeros.

-R suffix = RoHS compliant

Top View

HCM1103-R36-R &

HCM1103-R47-R

Top View

HCM1103-R12-R &

HCM1103-R68-R to

HCM1103-220R

Side View

Bottom View

Recommended Pad Layout

Schematic

Part Marking: xxx = Inductance value in uH, R = decimal point, if no R is present then third character = # of zeros.

wlyy = (Date code), R = Revision Level

All soldering surfaces to be coplanar within 0.10 millimeters.

Tolerances are ±0.3 millimeters unless stated otherwise.

HCM1103-R36-R and HCM1103-R47-R Color: Top Grey

HCM1103-R12-R and HCM1103-R68-R to HCM1103-220-R Color : Top Grey

Do not route traces or vias underneath the inductor

wlyy R

HCM1103-2R2-R 数据表(PDF) 2 Page - Eaton All Rights Reserved.

HCM1103-2R2-R 数据表(HTML) 2 Page - Eaton All Rights Reserved.

Html Pages

1 2 3 4 5 6 7

数据表下载