HCMA0503-R35-R datasheet(2/7 Pages) EATON

2 / 7 page

Technical Data

10248

Effective June 2016

HCMA0503

Automotive grade high current power inductors

www.eaton.com/elx

Product Specifications

Part Number6

OCL1

(μH) ± 20%

FLL2 (μH)

minimum

rms

(A)

sat

(A)

DCR (mΩ)

typical @ 20°C

DCR (mΩ)

maximum @ 20°C

K-factor5

HCMA0503-R20-R

0.20

0.13

22.2

21.0

2.1

2.31

1764

HCMA0503-R35-R

0.35

0.22

16.6

14.9

3.9

4.29

1259

HCMA0503-R47-R

0.47

0.30

12.0

11.5

6.5

7.15

820

HCMA0503-R75-R

0.75

0.48

11.3

9.7

8.5

9.35

801

HCMA0503-1R0-R

1.0

0.64

10.1

8.5

10.4

11.4

588

HCMA0503-1R5-R

1.5

0.96

7.5

7.0

17.1

18.5

393

HCMA0503-2R2-R

2.2

1.4

6.8

6.5

22.5

325

HCMA0503-3R3-R

3.3

2.1

5.5

6.0

36.4

40.4

273

HCMA0503-4R7-R

4.7

3.0

4.5

5.5

226

HCMA0503-5R6-R

5.6

3.6

4.25

3.5

70.6

206

HCMA0503-6R8-R

6.8

4.4

2.60

3.8

172

HCMA0503-100-R

6.4

2.75

2.3

122

132

158

HCMA0503-150-R

9.6

2.4

2.1

138

166

127

HCMA0503-220-R

1.9

260

270

106

1. Open Circuit Inductance (OCL) Test Parameters: 100 kHz, 0.25 Vrms, 0.0 Adc, +25 °C

2. Full Load Inductance (FLL) Test Parameters: 100 kHz, 0.25 Vrms, Isat, +25 °C

3. Irms: DC current for an approximate temperature rise of 40 °C without core loss. Derating is necessary for AC currents.

PCB layout, trace thickness and width, air-flow, and proximity of other heat generating components will affect the

temperature rise. It is recommended that the temperature of the part not exceed 125 °C under worst case operating

conditions verified in the end application.

4. Isat: Peak current for approximately 20% rolloff @ +25 °C

5. K-factor: Used to determine Bp-p for core loss (see graph). Bp-p = K * L * ΔI. Bp-p: (Gauss), K: (K-factor from table),

L: (Inductance in μH), ΔI (Peak to peak ripple current in Amps).

6. Part Number Definition: HCMA0503-xxx-R

HCMA0503 = Product code and size

xxx= inductance value in μH, R= decimal point,

If no R is present then last character equals number of zeros

-R suffix = RoHS compliant

Dimensions (mm)

Part marking: AXXX A=automotive, XXX=inductance value in uH, R= decimal point. If no R is present then last character equals number of zeros.

wly=date code, R=revision level

All soldering surfaces to be coplanar within 0.10 millimeters

Tolerances are ±0.2 millimeters unless stated otherwise

DCR measured from point “a” to point “b”

Color: Grey

Do not route traces or vias underneath the inductor

HCMA0503-R35-R 数据表(PDF) 2 Page - Eaton All Rights Reserved.

HCMA0503-R35-R 数据表(HTML) 2 Page - Eaton All Rights Reserved.

Html Pages

1 2 3 4 5 6 7

数据表下载