CS5334 datasheet(11/20 Pages) CIRRUS

11 / 20 page

P7 - Overrange

0 - Analog input less than full-scale level

1 - Analog input greater than full-scale

P6 - Idle channel

0 - Analog input >-60 dB from full-scale

1 - Analog input <-60 dB from full-scale

P5 to P0 - Peak Signal Level Bits (1 dB steps)

Inputs <0 dB

P5 - P0

0 dB

000000

-1 dB

000001

-2 dB

000010

-60 dB

111100

Inputs >0 dB

P5 - P0

0 dB

000000

+1 dB

000001

+2 dB

000010

+3 dB

000011

Bar Graph Mode

This mode provides a decoded output format

which indicates the peak Peak Signal Level in a

"Bar Graph" format.

Input Level

P7 - P0

Overflow

11111111

0 dB

to -3 dB

01111111

-3 dB

to -6 dB

00111111

-6 dB

to -10 dB

00011111

-10 dB to -20 dB

00001111

-20 dB to -30 dB

00000111

-30 dB to -40 dB

00000011

-40 dB to -60 dB

00000001

< - 60 dB

00000000

Overflow

Overflow indicates analog input overrange, for

both the Left and Right channels, since the last

update request on the Peak Update pin. A value

of 1 indicates an overrange condition. The left

channel information is output on OVFL during

the left channel portion of LRCK. The right

channel information is available on OVFL during

the right channel portion of LRCK.

Initialization

Upon initial power-up, the digital filters and

delta-sigma modulators are reset and the internal

voltage

reference

powered

down.

The

CS5334/5 will remain in the power-down mode

until valid clocks are presented. A valid MCLK

is required to exit power-down in Master Mode.

However, in Slave Mode, MCLK and LRCK of

the proper ratio are required to exit power-down.

MCLK occurrences are also counted over one

LRCK period to determine the MCLK / LRCK

frequency ratio in Slave Mode. Power is then ap-

plied to the internal voltage reference, the analog

inputs will move to approximately 2.2V and out-

put clocks will begin (Master Mode only). This

process requires 32 periods of LRCK and is fol-

lowed by the initialization sequence.

Initialization with High Pass Filter Enabled

28,672 LRCK cycles are required for the initiali-

zation sequence with the high pass filter enabled.

This time is dominated by the settling time re-

quired for the high pass filter.

Initialization and Internal Calibration with

High Pass Filter Disabled

If the HP DEFEAT pin is high (high pass filter

disabled) during the initialization sequence, the

CS5334/5 will perform an internal dc calibration

by:

1. disconnecting the internal ADC inputs from

the input pins,

2. connecting the (differential) ADC inputs to a

common reference voltage,

CS5334 CS5335

DS237PP2

CS5334 数据表(PDF) 11 Page - Cirrus Logic

CS5334 数据表(HTML) 11 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

数据表下载

链接网址

CS5334 数据表(PDF) 11 Page - Cirrus Logic

CS5334 数据表(HTML) 11 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

数据表 下载

链接网址

数据表下载