Specifications

Supply Voltage and Current

10 V dc to 30 V dc (10% maximum ripple) at less than 45 mA,

exclusive of load

Supply Protection Circuitry

Protected against reverse polarity and transient voltages

Adjustments

Push-button TEACH mode sensitivity setting; remote TEACH mode

input is provided

Indicators

Two LEDs: amber and bi-color green/red

Construction

Reinforced thermoplastic polyester housing, totally encapsulated, o-

ring seal, acrylic lenses, and stainless steel screws.

Required Overcurrent Protection

WARNING: Electrical connections must be made by

qualified personnel in accordance with local and

national electrical codes and regulations.

Overcurrent protection is required to be provided by end product

application per the supplied table.

Overcurrent protection may be provided with external fusing or via

Current Limiting, Class 2 Power Supply.

Supply wiring leads < 24 AWG shall not be spliced.

For additional product support, go to http://

www.bannerengineering.com.

Supply Wiring (AWG)

Required Overcurrent Protection (Amps)

20

5.0

22

3.0

24

2.0

26

1.0

28

0.8

30

0.5

Connections

PVC-jacketed 5-conductor 2 m (6.5 ft) or 9 m (30 ft) unterminated

cable, or 5-pin Euro-style quick-disconnect (QD) fitting are available.

QD cables are ordered separately.

Application Notes

The first condition presented during TEACH mode becomes the output

ON condition.

Output Configuration

Bipolar: One current sourcing (PNP) and one current sinking (NPN)

open-collector transistor

Output Rating

150 mA maximum each output at 25° C, derated to 100 mA at 70° C

(derate ≈1 mA per °C)

Off-state leakage current: less than 5 μA at 30 V dc

ON-state saturation current: less than 1 V at 10 mA; less than 1.5 V at

150 mA

Output Protection Circuitry

Protected against false pulse on power-up and continuous overload or

short-circuit of outputs

Output Response Time

Sensors will respond to either a “light” or a “dark” signal of 500

microseconds or longer duration, 1 kHz max.

NOTE: 1 second delay on power-up; outputs do not

conduct during this time.

Repeatability

100 microseconds (all models)

Rating

Meets NEMA standards 1, 2, 3, 3S, 4, 4X, 6, 12, and 13; IEC IP67

Operating Conditions

Temperature: –20° to +70° C (–4° to +158° F)

Max. Relative Humidity: 90% at 50° C (non-condensing)

Dimensions

Cabled Models

(Suffix E, EL, EPD, R, RL, RPD, LV, LVAG, LP, LPC, D, C, C2,

CV, CV2, CVG, CV2G, CVB, CV2B, CVW )

3.2 mm (0.13”)

12.2 mm (0.48”)

3 mm dia Clearance (2)

M18 × 1 × 15 mm Thread

(Mounting nut supplied)

27.4 mm (1.08”)

53.3 mm (2.10”)

19.1 mm (0.75”)

Mounting peg

(6.3 mm dia × 2.5 mm)

2 m (6.5’) Cable

30.7 mm

(1.21”)

24.1 mm

(0.95”)

Divergent Diffuse Models

(Suffix DBZ and W)

3 mm dia Clearance (2)

Bezel

18.0 mm (0.71”)

13.2 mm (0.52”)

39.1 mm

(1.54”)

MINI-BEAM SME312 Expert Series

6

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 55214 Rev. G