Wiring

On-Axis Light Wire

Terminal Block

External Power Supply

(Strobed)

External Power Supply

(Continuous)

Brown

Pin 1, +V (24 V dc ±10%)

+V

+V

Blue

Pin 2, -V (dc common)

-V

-V

Black

Pin 4 (strobe)

+5 V dc to 24 V dc OFF

-V

-V ON

Specifications

Light Source

Visible red LED, 630 nm ; Infrared, 880 nm ; Visible blue, 470 nm; White, 5500

K, or Green

Supply Voltage and Current

24 V dc ± 10% 500 mA maximum, 125 mA maximum for 50 mm models.

Direct connect to

PresencePLUS P4 sensor operating at 24 V dc only

Use only with a suitable Class 2 power supply (UL) or SELV power supply (CE)

Construction

Housing: aluminum with black anodizing

Beam Splitter: optical glass with optical coatings on both sides

Diffuser: high-precision cast acrylic

Dust Cover: optical glass with broadband anti-reflective coating (425 nm to

675 nm) (some models)

Useful Life

When operated within specifications, output will decrease less than 20% after

10,000 hours and less than 30% after 20,000 hours (based on continuous

operation).

Note: Actual useful life of strobed lights depends on

duty cycle.

Operating Conditions

Temperature: 0 °C to +50 °C (+32 °F to +122 °F)

Humidity: 90% at +50 °C maximum relative humidity (non-condensing)

Cleaning Instructions

Handle the sensor with care during installation and operation. Sensor

windows soiled by fingerprints, dust, water, oil, etc. may create stray light

that may degrade the peak performance of the sensor. Blow the window

clear using filtered, compressed air, then clean as necessary using a lens

cloth and lens cleaner or window cleaner. Do not use any other chemicals

for cleaning.

Installation

Before installing an on-axis light, it is recommended that the listed

ambient light filter be installed behind the camera lens. The filter improves

image quality by reducing unwanted ambient light.

•

100 mm models: 50 × 50 mm suggested field of view and 25

mm minimum suggested stand off

•

50 mm models: 25 × 25 mm suggested field of view and 25 mm

minimum suggested stand off

Certification

Dimensions

All measurements are listed in millimeters [inches], unless noted otherwise.

147.8 mm (5.82")

87.5 mm (3.44")

29.9 mm (1.18")

29.9 mm (1.18")

5.5 mm (0.22")

4X 1/4-20 UNC

29.6 mm

(1.17")

38.1 mm

(1.50")

59.8 mm

(2.36")

3X 1/4-20 UNC

10.9 mm

(0.43")

114.5 mm (4.5")

59.3 mm

(2.33")

Figure 2. 55 mm Models

178.0 mm (7.01")

109.3 mm

(4.30")

190.3 mm (7.49")

109.9 mm (4.33")

38.1 mm

(1.50")

35.9 mm

(1.41")

54.9 mm (2.16")

54.6 mm

(2.15")

5.5 mm (0.22")

138.0 mm (5.43")

3X 1/4-20 UNC

54.9 mm (2.16")

4X 1/4-20 UNC

Figure 3. 100 mm Models

LED..O..M Series Diffused On-Axis Lights

2

www.bannerengineering.com - Tel: + 1 888 373 6767

P/N 126059 Rev. M