Banner Engineering Corp., 9714 Tenth Ave. No., Mpls., MN 55441 • Ph: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com

LED Diffused On-Axis Lights (75 mm)

P/N 67439 rev. A

Strobe Control Module (see data sheet p/n 67448)

Models

Input

Trigger Input

Output

Output Pulse

Range

Used with

24V dc ±5%

2 A max.

5 - 12V dc

pulse rising or

falling (switch

selectable)

10 mA max.

2-channels

24V dc ±5%

9 A nominal per

channel @ 60 Hz

5 to 1,300

microseconds

Strobed types:

LEDWO75N-S

LEDRO75N-S

(Use Power Supply PSC-24

or PSC-24E)

Variable Power Supplies (see data sheet p/n 67449)

Models

Input

Input Cord

Output

Output Cable

Used with

100-140V ac

60 Hz

North America

(NEMA 5-15)

2-channels

6 - 12V dc

2 A max. per

channel

1.8 m (6')

Terminated with

9-pin D-sub

connector

(female pins)

Continuous types:

LEDWO75N

LEDBO75N

LEDRO75N

LEDRO75N-H

200-250V ac

50 Hz

Cont. Europe

(Schuko CEE 7)

Continuous Power Supplies

Models

Input

Input Cord

Output

Output Cable

Used with

PSA-12

100-250V ac

50/60 Hz

North America

(NEMA 5-15)

12V dc ±5%

with voltage

regulation of ±1%

3.5 A max.

1.8 m (6')

Terminated

with 9-pin D-

sub connector

(female pins)

Continuous types:

LEDWO75N

LEDBO75N

LEDRO75N

LEDRO75N-H

PSA-12E

Cont. Europe

(Schuko CEE 7)

100-250V ac

50/60 Hz

North America

(NEMA 5-15)

24V dc ±5%

with voltage

regulation of ±1%

2.2 A max.

1.8 m (6')

2-wire

Unterminated

SCM Strobe

Control Module

(see below)

Cont. Europe

(Schuko CEE 7)

Banner Engineering Corp., 9714 Tenth Ave. No., Mpls., MN 55441 • Ph: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com

Accessories

Extension Cables

Models

Length

Configuration

Used with

1.8 m (6')

Terminated both ends with 9-pin D-sub connector, for continuous lights

(one end male pins and opposite end female pins)

Continuous types:

LEDWO75N

LEDBO75N

LEDRO75N

LEDRO75N-H

3.0 m (10'')

1.8 m (6')

Y cable for powering 2 lights from one supply, for continuous lights

1.8 m (6')

Terminated both ends with 9-pin D-sub connector, for strobed lights

(one end male pins and opposite end female pins)

Strobed types:

LEDWO75N-S

LEDRO75N-S

3.0 m (10')

1.8 m (6')

Y cable for powering 2 lights from one supply, for strobed lights

WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner

Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the

time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the

improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied.