X9420WS datasheet(10/20 Pages) INTERSIL

10 / 20 page

FN8195.0

March 7, 2005

ABSOLUTE MAXIMUM RATINGS

Temperature under bias .................... -65°C to +135°C

Storage temperature ......................... -65°C to +150°C

Voltage on SCK, SCL or any

address input with respect to VSS ........... -1V to +7V

Voltage on V+ (referenced to VSS)........................ 10V

Voltage on V- (referenced to VSS)........................-10V

(V+) - (V-) .............................................................. 12V

Any VH/RH, VL/RL, VW/RW ........................... V- to V+

Lead temperature (soldering, 10 seconds) ........ 300°C

IW (10 seconds)..................................................±6mA

COMMENT

Stresses above those listed under “Absolute Maximum

Ratings” may cause permanent damage to the device.

This is a stress rating only; functional operation of the

device (at these or any other conditions above those

listed in the operational sections of this specification)

is not implied. Exposure to absolute maximum rating

conditions for extended periods may affect device

reliability.

ANALOG CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)

Notes: (1) Absolute Linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as

a potentiometer.

(2) Relative Linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potenti-

ometer. It is a measure of the error in step size.

(3) MI = RTOT/63 or (VH - VL)/63, single pot.

(4) Typical = Individual array resolution.

Symbol

Parameter

Limits

Test Conditions

Min.

Typ.

Max.

Units

RTOTAL

End to End Resistance

±20

Power Rating

25°C, each pot

Wiper Current

±3

Wiper Resistance

150

250

Ω

Wiper Current =

± 1mA,

V+/V- = ±3V

100

Ω

Wiper Current =

± 1mA,

V+/V- = ±5V

Vv+

Voltage on V+ Pin

X9420

+4.5

+5.5

X9420-2.7

+2.7

+5.5

Vv-

Voltage on V- Pin

X9420

-5.5

-4.5

X9420-2.7

-5.5

-2.7

VTERM

Voltage on any VH/RH, VL/RL, VW/RW

V-

V+

Noise

-140

dBV

Ref: 1kHz

Resolution(4)

1.6

See Note 5

Absolute Linearity(1)

±1

MI(3)

Vw(n)(actual) - Vw(n)(expected)

Relative Linearity(2)

±0.2

MI(3)

Vw(n + 1) - [Vw(n) + MI]

Temperature Coefficient of RTOTAL

±300

ppm/°C

See Note 5

Ratiometric Temperature Coefficient

±20

ppm/°C

See Note 5

CH/CL/CW Potentiometer Capacitances

10/10/25

See Circuit #3

IAL

Rh, RI, Rw leakage current

0.1

µA

Vin = V- to V+. Device is in

stand-by mode.

RECOMMENDED OPERATING CONDITIONS

Temp

Min.

Max.

Commercial

°C+70°C

Industrial

-40

°C+85°C

Device

Supply Voltage (VCC) Limits

X9420

± 10%

X9420-2.7

2.7V to 5.5V

X9420

X9420WS 数据表(PDF) 10 Page - Intersil Corporation

X9420WS 数据表(HTML) 10 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

数据表下载

链接网址

X9420WS 数据表(PDF) 10 Page - Intersil Corporation

X9420WS 数据表(HTML) 10 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

数据表 下载

链接网址

数据表下载