AHP201208FA-R68M datasheet(3/6 Pages) TAI-TECH

3 / 6 page

TAI-TECH

www.tai-tech.com.tw

6. Reliability and Test Condition

Item

Performance

Test Condition

Operating temperature

-40~+125℃ (Including self - temperature rise)

Storage temperature

-40~+125℃ (on board)

Electrical Performance Test

Inductance

Refer to standard electrical characteristics list.

HP4284A,CH11025,CH3302,CH1320,CH1320S

LCR Meter.

DCR

CH16502,Agilent33420A Micro-Ohm Meter.

Saturation Current (Isat)

△L≦30% typical.

Saturation DC Current (Isat) will cause L0

to drop △L(%)(keep quickly).

Heat Rated Current (Irms)

Approximately △T≦40℃

Heat Rated Current (Irms) will cause the coil temperature rise

△T(℃) without core loss.

1.Applied the allowed DC current(keep 1 min.).

2.Temperature measured by digital surface thermometer

Reliability Test

Life Test

Appearance：No damage.

Inductance：within±10% of initial value

Q：Shall not exceed the specification value.

RDC：within ±15% of initial value and shall not

exceed the specification value

Preconditioning: Run through IR reflow for 2 times.( IPC/JEDEC

J-STD-020DClassification Reflow Profiles)

Temperature

： 125±2℃(Inductor)

Applied current

：rated current

Duration

：1000±12hrs

Measured at room temperature after placing for 24±2 hrs

Load Humidity

Preconditioning: Run through IR reflow for 2 times.( IPC/JEDEC

J-STD-020DClassification Reflow Profiles

Humidity

：85±2﹪R.H,

Temperature

：85℃±2℃

Duration

：1000hrs Min. with 100% rated current

Measured at room temperature after placing for 24±2 hrs

Moisture Resistance

Preconditioning: Run through IR reflow for 2 times.( IPC/JEDEC

J-STD-020DClassification Reflow

Profiles

1. Baked at50℃ for 25hrs, measured at room temperature after

placing for 4 hrs.

2. Raise temperature to 65±2℃ 90-100%RH in 2.5hrs, and

keep 3 hours, cool down to 25℃ in 2.5hrs.

3. Raise temperature to 65±2℃ 90-100%RH in 2.5hrs, and

keep 3 hours, cool down to 25℃ in

2.5hrs,keep at 25℃ for 2 hrs then keep at -10℃ for 3 hrs

4. Keep at 25℃ 80-100%RH for 15min and vibrate at the

frequency of 10 to 55 Hz to 10 Hz, measure at

room temperature after placing for 1~2 hrs.

Thermal

shock

Preconditioning: Run through IR reflow for 2 times.( IPC/JEDEC

J-STD-020DClassification

Reflow Profiles

Condition for 1 cycle

Step1

：-40±2℃ 30±5min

Step2

：25±2℃ ≦0.5min

Step3

：125±2℃ 30±5min

Number of cycles

： 500

Measured at room temperature after placing for 24±2 hrs

Vibration

Oscillation Frequency: 10Hz～2KHz～10Hz for 20 minute

Equipment： Vibration checker

Total Amplitude:10g

Testing Time : 12 hours(20 minutes, 12 cycles each of 3

orientations)。

Test the quantity：15pcs

AHP201208FA-R68M 数据表(PDF) 3 Page - TAI-TECH Advanced Electronics Co., Ltd.

AHP201208FA-R68M 数据表(HTML) 3 Page - TAI-TECH Advanced Electronics Co., Ltd.

Html Pages

1 2 3 4 5 6

数据表下载

链接网址

AHP201208FA-R68M 数据表(PDF) 3 Page - TAI-TECH Advanced Electronics Co., Ltd.

AHP201208FA-R68M 数据表(HTML) 3 Page - TAI-TECH Advanced Electronics Co., Ltd.

Html Pages

1 2 3 4 5 6

数据表 下载

链接网址

数据表下载