ATS616LSG datasheet(3/14 Pages) ALLEGRO

3 / 14 page

ATS616LSG-DS, Rev. 1

Worcester, Massachusetts 01615-0036 (508) 853-5000

115 Northeast Cutoff, Box 15036

www.allegromicro.com

Allegro MicroSystems, Inc.

Dynamic Self-Calibrating Peak-Detecting Differential Hall Effect Gear Tooth Sensor

ATS616LSG

OPERATING CHARACTERISTICS over operating voltage and temperature range, unless otherwise noted

Characteristic

Symbol

Test Condition

Min.

Typ.1

Max.

Units

ELECTRICAL CHARACTERISTICS

Supply Voltage2

VCC

Operating, TJ < 165°C

3.5

–

Power-On State

POS

VCC = 0 → 5 V

–

HIGH

–

Undervoltage Lockout Threshold

VCC(UV) VCC = 0 → 5 V; VCC = 5 → 0 V

–

3.5

Output On Voltage

VOUT(SAT) IOUT = 20 mA

–

200

400

Supply Zener Clamp Voltage

VZsupply ICC = 16 mA, TA = 25°C

–

Output Zener Clamp Voltage

VZoutput IOUT = 3 mA, TA = 25°C

–

Supply Zener Current

IZsupply

VS = 28 V

–

Output Zener Current

IZoutput

VOUT = 30 V

–

Output Current Limit

IOUTM

VOUT = 12 V

Output Leakage Current

IOUTOFF VOUT = 24 V

–

μA

Supply Current

ICC

VCC > VCC(min)

Power-On Time

tPO

VCC > 5 V

–

500

μs

Output Rise Time3

RLOAD = 500 Ω, CS = 10 pF

–

0.3

5.0

μs

Output Fall Time3

RLOAD = 500 Ω, CS = 10 pF

–

0.2

5.0

μs

PERFRORMANCE CHARACTERISTICS

Operating Air Gap Range

Operating within specification, Target Speed > 10 rpm

0.4

–

2.5

Operating Magnetic Flux Density

Differential4

BAG(p-p) Operating within specification, Target Speed > 10 rpm

–

Operating Frequency

–

10 000

Initial Calibration Cycle5

ncal

Output edges before calibration is completed, at fsig<100Hz

Edge

Calibration Mode Disable

ndis

Output falling edges for startup calibration to be complete

Edge

Relative Timing Accuracy, Sequential

Eθ

Target Speed = 1000 rpm, BAG(p-p) > 100 G

–

±0.5

±0.75

(°)

Target Speed = 1000 rpm, BAG(p-p) > 60 G

–

±1.5

(°)

Allowable User Induced Differential Offset4

ΔBApp

Output switching only; may not meet data sheet specifica-

tions

–

±50

1Typical data is at VCC = 8 V and TA = 25°C. Performance may vary for individual units, within the specified maximum and minimum limits.

2 Maximum voltage must be adjusted for power dissipation and junction temperature; see Power Derating section.

3 CS is the probe capacitance of the oscilloscope used to make the measurement.

4 10 G = 1 mT (millitesla), exactly.

5Non-uniform magnetic profiles may require additional edges before calibration is complete.

ATS616LSG 数据表(PDF) 3 Page - Allegro MicroSystems

ATS616LSG 数据表(HTML) 3 Page - Allegro MicroSystems

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14

数据表下载