E5CS

4

■ Characteristics

Note: 1. The following exceptions apply to thermocouples.

• U, L: ±2°C ±1 digit max.

• R:

±3

°C ±1 digit max. at 200°C or less

2. The following exception applies to platinum resistance thermometers.

• Input set values 1 for E5CS-U: 1% FS ±1 digit max.

3. The following exceptions apply to thermistors.

• When the unit setting is °C, temperature indication ranges exceeding the set temperature range ±10% FS may not be accurate.

• When the unit setting is °F, the temperature range for the input setting numbers 4 and 9 (609 to 630°F) and temperature indication

ranges exceeding the set temperature range

−5% FS to +10% FS may not be accurate.

4. Industrial electromagnetic environment (EN/IEC 61326-1 Table 2)

Setting accuracy

Thermocouple (See note 1.):

(±1% of indication value or ±2

°C, whichever is greater) ±1 digit max.

Platinum resistance thermometer (See note 2.): (±0.5% of indication value or ±1

°C, whichever is greater) ±1 digit max.

Thermistor (See note 3.):

(1% FS of indication value) ±1 digit max.

Indication accuracy

(ambient temperature of 23

°C)

Influence of temperature

R thermocouple inputs:

(±2% of PV or ±10

°C, whichever is greater) ±1 digit max.

Other thermocouple inputs:

(±2% of PV or ±4

°C, whichever is greater) ±1 digit max.

Platinum resistance thermometer inputs: (±1% of PV or ±2

°C, whichever is greater) ±1 digit max.

Thermistor:

(±2% FS) ±1 digit max.

Influence of voltage

Influence of EMS.

(at EN 61326-1)

Hysteresis (for ON/OFF control)

0.2% FS (0.1% FS for universal-input (thermocouple/platinum resistance thermometer) models)

Proportional band (P)

1 to 999

°C (automatic adjustment using auto-tuning/self-tuning)

Integral time (I)

1 to 1,999 s (automatic adjustment using auto-tuning/self-tuning)

Derivative time (D)

1 to 1,999 s (automatic adjustment using auto-tuning/self-tuning)

Alarm output range

Absolute-value alarm: Same as the control range

Other:

0 to input setting range full scale (

°C or °F)

Alarm hysteresis:

0.2

°C or °F (fixed)

Control period

2/20 s

Sampling period

500 ms

Insulation resistance

20 M

Ω min. (at 500 VDC)

Dielectric strength

2,000 VAC, 50/60 Hz for 1 min between current-carrying terminals of different polarity

Vibration

resistance

Destruction 10 to 55 Hz, 0.75-mm single amplitude for 2 hr each in X, Y, and Z directions

Shock resistance

Life expectancy

Electrical

100,000 operations min. (relay output models)

Weight

Approx. 110 g (Controller only)

Degree of protection

Front panel: Equivalent to IP50, Enclosure Category 2 (IEC 60529), Rear case: IP20; Terminals: IP00

Memory protection

EEPROM (non-volatile memory) (number of writes: 1,000,000)

EMC

EMI Radiated:

EN 55011 Group 1 Class A

EMI Conducted:

EN 55011 Group 1 Class A

Radiated Electromagnetic Field Immunity:

EN 61000-4-2: 4 kV contact discharge (level 2)

8 kV air discharge (level 3)

RF-interference Immunity:

EN 61000-4-3: 10 V/m (80-1000 MHz, 1.4-2.0 GHz amplitude modulated) (level 3)

10 V/m (900 MHz pulse modulated)

Conducted Disturbance Immunity:

EN 61000-4-6: 3 V (0.15 to 80 MHz) (level 2)

Noise Immunity (First Transient Burst Noise): EN 61000-4-4

Burst Immunity:

2 kV power-line (level 3), 1 kV I/O signal-line (level 3)

Surge Immunity:

EN 61000-4-5: Power line:

Normal mode 1 kV; Common mode 2 kV

Output line (relay output): Normal mode 1 kV; Common mode 2 kV

Voltage Dip/Interrupting Immunity:

EN 61000-4-11 0.5 cycle, 100% (rated voltage)

Approved standards

UL 61010-1 (listing)

CSA C22.2 No.1010-1

Conformed standards

EN 61326-1 (See note 4.), EN 61010-1, IEC 61010-1