5000 datasheet(32/42 Pages) TI

32 / 42 page

TSW-110-02-S-D

+5V

0.1uF

GND

X6-1

X6-2

X6-3

X6-4

X6-5

X6-6

X6-7

X6-8

X6-9

X6-10

X6-11

X6-12

X6-13

X6-14

X6-15

X6-16

X6-17

X6-18

X6-19

X6-20

X7-1

X7-2

X7-3

X7-4

X7-5

X7-6

X7-7

X7-8

X7-9

X7-10

X7-11

X7-12

X7-13

X7-14

X7-15

X7-16

X7-17

X7-18

X7-19

X7-20

X8-1

X8-2

X8-3

X8-4

X8-5

X8-6

X8-7

X8-8

X8-9

X8-10

X8-11

X8-12

X8-13

X8-14

X8-15

X8-16

X8-17

X8-18

X8-19

X8-20

X9-1

X9-2

X9-3

X9-4

X9-5

X9-6

X9-7

X9-8

X9-9

X9-10

X9-11

X9-12

X9-13

X9-14

X9-15

X9-16

X9-17

X9-18

X9-19

X9-20

R19

R20

JP4

JP5

C23

C24

C25

C26

PB2

PB3

PL0

PP2

PH2

GND/1.6B

TARGET_RESET/3.2D

PA0/3.2C

BP2_A2.5

TARGET_RXD/6.1D

TARGET_TXD/6.1D

PA1/3.2C

BP2_A2.6

PE4

PE5

PC5

PC4

PM3

PM4

PM5

PL4

PD5/1.4B

PC6

PD3

PC7

PE0

PE1

PE2

PE3

PD4/1.4B

PD7

PF1

PF2

PF3

PG0

PL5

PL1

PL2

PL3

PH3

PD1

PD0

PN2

PN3

PD2

PP0

PP1

PQ0

PP4

PN5

PN4

PB4

PB5

PK0

PK1

PK2

PK3

PA4

PA5

PG1

PK4

PK5

PM0

PM1

PM2

PH0

PH1

PK6

PK7

PM7

PA7

PA3

PA2

PQ3

PQ2

PP3

PQ1

PM6

PP5

PA6

BoosterPack 2 Interface

BoosterPack 1 Interface

JP4 and JP5 CAN and ICDI UART Selection:

Populate Jumpers from 1-2 and 3-4 for Default Mode

This enables ROM UART boot loader. UART 0 to ICDI

Populate from 1-3 and 2-4 for controller area network

on the boosterpack. UART2 is then availabe to ICDI.

R19 and R20 can be populated to enable I2C on

Right side of BP2 interface. This is for legacy

support and the Sensor Hub BoosterPack.

I2C and SSI are available on the corresponding

BoosterPack 1 interface pins without modification to

the board.

PA6 and PA7 are also used by the onboard radio.

Configure the radio to tri-state these GPIO before

using them on the boosterpack interface.

5000 数据表(PDF) 32 Page - Texas Instruments

5000 数据表(HTML) 32 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

数据表下载