IS25LP064A-RBLE1 datasheet(65/99 Pages) ISSI

65 / 99 page

IS25LP064A/032A

Integrated Silicon Solution, Inc.- www.issi.com

Rev. A

11/06/2015

8.31 SOFTWARE RESET (RESET-ENABLE (RSTEN, 66h) AND RESET (RST, 99h)) AND HARDWARE RESET

The Software Reset operation is used as a system reset that puts the device in normal operating mode. During

the Reset operation, the value of volatile registers will default back to the value in the corresponding non-volatile

requires the Reset-Enable command followed by the Reset command. Any command other than the Reset

command after the Reset-Enable command will disable the Reset-Enable.

Execute the CE# pin low  sends the Reset-Enable command (66h), and drives CE# high. Next, the host drives

CE# low again, sends the Reset command (99h), and pulls CE# high.

Only for the parts that have the RESET# function option, Hardware Reset function is available. For all packages

with RESET# (IO3) option except 16-pin SOIC/24-ball TFBGA with dedicated RESET# function, the RESET#

pin will be solely applicable in SPI mode and when the QE bit is disabled. For 16-pin SOIC/24-ball TFBGA

packages with dedicated RESET# function, the RESET# pin (or ball) is always applicable regardless of the QE

bit value.

The dedicated RESET# pin (or ball) has an internal pull-up resistor and may be left floating if not used The

RESET# pin (or ball) has the highest priority among all the input signals and will reset the device to its initial

power-on state regardless of the state of all other pins (CE#, IOs, SCK, and WP#).

In order to activate Hardware Reset, the RESET# pin (or ball) must be driven low for a minimum period of t

RESET

(1µs). Drive RESET# low for a minimum period of t

RESET will interrupt any on-going internal and external

operations, release the device from deep power down mode

1, disable all input signals, force the output pin enter

a state of high impedance, and reset all the read parameters. If the RESET# pulse is driven for a period shorter

than 1µs, it may still reset the device, however the 1µs minimum period is recommended to ensure the reliable

operation. The required wait time after activating a HW Reset before the device will accept another instruction

(tHWRST) is the same as the maximum value of tSUS (100µs).

The Software/Hardware Reset during an active Program or Erase operation aborts the operation, which can

result in corrupting or losing the data of the targeted address range. Depending on the prior operation, the reset

timing may vary. Recovery from a Write operation will require more latency than recovery from other operations.

Note 1: The Status and Function Registers remain unaffected.

Figure 8.50 Software Reset Enable and Software Reset Sequence (RSTEN, 66h + RST, 99h)

Instruction = 66h

CE#

SCK

Mode 3

Mode 0

Instruction = 99h

High Impedance

IS25LP064A-RBLE1 数据表(PDF) 65 Page - Integrated Silicon Solution, Inc

IS25LP064A-RBLE1 数据表(HTML) 65 Page - Integrated Silicon Solution, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99

数据表下载