IS25LP032D-RKLE datasheet(9/118 Pages) ISSI

9 / 118 page

IS25LP032D

IS25WP032D

Integrated Silicon Solution, Inc.- www.issi.com

Rev. A12

08/04/2020

2. PIN DESCRIPTIONS

SYMBOL

TYPE

DESCRIPTION

CE#

INPUT

Chip Enable: The Chip Enable (CE#) pin enables and disables the devices

operation. When CE# is high the device is deselected and output pins are in a high

impedance state. When deselected the devices non-critical internal circuitry power

down to allow minimal levels of power consumption while in a standby state.

When CE# is pulled low the device will be selected and brought out of standby mode.

The device is considered active and instructions can be written to, data read, and

written to the device. After power-up, CE# must transition from high to low before a

new instruction will be accepted.

Keeping CE# in a high state deselects the device and switches it into its low power

state. Data will not be accepted when CE# is high.

SI (IO0),

SO (IO1)

INPUT/OUTPUT

Serial Data Input, Serial Output, and IOs (SI, SO, IO0, and IO1):

This device supports standard SPI, Dual SPI, and Quad SPI operation. Standard SPI

instructions use the unidirectional SI (Serial Input) pin to write instructions,

addresses, or data to the device on the rising edge of the Serial Clock (SCK).

Standard SPI also uses the unidirectional SO (Serial Output) to read data or status

from the device on the falling edge of the serial clock (SCK).

In Dual and Quad SPI mode, SI and SO become bidirectional IO pins to write

instructions, addresses or data to the device on the rising edge of the Serial Clock

(SCK) and read data or status from the device on the falling edge of SCK. Quad

SPI instructions use the WP# and HOLD# pins as IO2 and IO3 respectively.

WP# (IO2)

INPUT/OUTPUT

Write Protect/Serial Data IO (IO2): The WP# pin protects the Status Register from

being written in conjunction with the SRWD bit. When the SRWD is set to “1” and the

WP# is pulled low, the Status Register bits (SRWD, QE, BP3, BP2, BP1, BP0) are

write-protected and vice-

versa for WP# high. When the SRWD is set to “0”, the Status

When the QE bit is set to “1”, the WP# pin (Write Protect) function is not available

since this pin is used for IO2.

HOLD# (IO3)

RESET# (IO3)

INPUT/OUTPUT

HOLD# or RESET#/Serial Data IO (IO3): When the QE bit of Status Register is set

to “1”, HOLD# pin or RESET# is not available since it becomes IO3.

Most packages except for 16-pin SOIC and 24-ball BGA:

When QE=0, the pin acts as HOLD# or RESET# and either one can be selected by

the P7 bit setting in Read Register. HOLD# will be selected if P7=0 (Default) and

RESET# will be selected if P7=1.

16-pin SOIC and 24-ball BGA packages :

When QE=0 and Dedicated RESET# is Enabled (Default), the pin acts as

HOLD# regardless of the P7 bit setting in Read Register.

When QE=0 and Dedicated RESET# is Disabled, the pin acts as HOLD# or

RESET# and either one can be selected by the P7 bit setting in Read Register.

HOLD# will be selected if P7=0 (Default) and RESET# will be selected if P7=1.

The HOLD# pin allows the device to be paused while it is selected. It pauses serial

communication by the master device without resetting the serial sequence. The

HOLD# pin is active low. When HOLD# is in a low state and CE# is low, the SO pin

will be at high impedance. Device operation can resume when HOLD# pin is brought

to a high state.

IS25LP032D-RKLE 数据表(PDF) 9 Page - Integrated Silicon Solution, Inc

IS25LP032D-RKLE 数据表(HTML) 9 Page - Integrated Silicon Solution, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

IS25LP032D-RKLE 数据表(PDF) 9 Page - Integrated Silicon Solution, Inc

IS25LP032D-RKLE 数据表(HTML) 9 Page - Integrated Silicon Solution, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载