1. DISPLAY: 8 digit LCD 0.46" (11.7 mm) high digits

CUB5R000: Reflective LCD with full viewing angle

CUB5B000: Transmissive LCD with selectable red or green LED backlight,

viewing angle optimized. Display color change capability with output state

when using an output module.

2. POWER: Input voltage range is +9 to +28 VDC with short circuit and input

polarity protection. Must use an RLC model MLPS or an NEC Class 2 or

Limited Power Source (LPS) rated power supply.

MODEL

NO.

DISPLAY COLOR

INPUT CURRENT

@ 9 VDC WITHOUT

CUB5RLY0

INPUT CURRENT

@ 9 VDC WITH

CUB5RLY0

CUB5R000

---

10 mA

30 mA

CUB5B000

Red (max intensity)

85 mA

115 mA

CUB5B000

Green (max intensity)

95 mA

125 mA

3. COUNTER DISPLAYS:

Counter A: 8-digits, enabled in all count modes

Display Range: -9999999 to 99999999

Counter B: 7-digits, enabled in Dual Counter Mode or batch counting

Display Range: 0 to 9999999 (positive count only)

Maximum Count Rates: 50% duty cycle

Without setpoint option card: 20 KHz (all count modes)

With setpoint option card: 20 KHz for any count mode except Dual Counter

(16 KHz), Quadrature x2 (14 KHz) and Quadrature x4 (13 KHz).

4. RATE DISPLAY: 6-digits, may be enabled or disabled in any count mode

Display Range: 0 to 999999

Maximum Frequency: 20 KHz

Minimum Frequency: 0.01 Hz

Accuracy: ±0.01%

5. COUNT/RATE SIGNAL INPUTS (INP A and INP B):

Input A: DIP switch selectable to accept pulses from a variety of sources.

See Section 2.0 Setting the DIP Switches for Input A specifications.

Input B: Logic signals only

Current sinking: Internal 10KΩ pull-up resistor to +9 to 28 VDC

Filter (LO Freq.): Damping capacitor provided for switch contact bounce.

Limits input frequency to 50 Hz and input pulse widths to 10 msec min.

6. USER INPUT (USR): Programmable input. Connect to input common (INP

COMM) to activate function. Internal 10KΩ pull-up resistor to +9 to 28 VDC.

Response Time: 5 msec typ.; 50 msec debounce (activation and release)

parameters and count values when power is removed.

8. CONNECTIONS: Wire clamping screw terminals

Wire Strip Length: 0.3" (7.5 mm)

Wire Gage: 30-14 AWG copper wire

Torque: 3.5 inch-lbs (0.395 N-m) max.

9. CONSTRUCTION: This unit rated for Type 4X/IP65 requirements for indoor/

outdoor use. Installation Category I, Pollution Degree 2. High impact plastic

case with clear viewing window. Panel gasket and mounting clip included.

10. ENVIRONMENTAL CONDITIONS:

Operating Temperature Range for CUB5R000: -35 to 75 °C

Operating Temperature Range for CUB5B000 depends on display color

and intensity level as per below:

INTENSITY LEVEL

TEMPERATURE

Red Display

1 & 2

-35 to 75°C

3

-35 to 70°C

4

-35 to 60°C

5

-35 to 50°C

Green Display

1 & 2

-35 to 75°C

3

-35 to 65°C

4

-35 to 50°C

5

-35 to 35°C

Storage Temperature: -35 to 85 °C

Operating and Storage Humidity: 0 to 85% max. relative humidity (non-

condensing)

Vibration to IEC 68-2-6: Operational 5-500 Hz, 5 g

Shock to IEC 68-2-27: Operational 40 g

Altitude: Up to 2000 meters

11. CERTIFICATIONS AND COMPLIANCES:

CE Approved

EN 61326-1 Immunity to Industrial Locations

Emission CISPR 11 Class A

Safety requirements for electrical equipment for measurement, control, and

laboratory use:

EN 61010-1: General Requirements

EN 61010-2-030: Particular Requirements for Testing and Measuring

Circuits

RoHS Compliant

UL Recognized Component: File #E179259

UL Listed: File #E137808

Type 4X Indoor/Outdoor Enclosure rating (Face only)

IP65 Enclosure rating (Face only)

IP20 Enclosure rating (Rear of unit)

Refer to EMC Installation Guidelines for additional information.

12. WEIGHT: 3.2 oz (100 g)

2

TYPE

MODEL NO.

DESCRIPTION

PART NUMBER

CUB5

CUB5R

Dual Counter & Rate Indicator with Reflective Display

CUB5R000

CUB5B

Dual Counter & Rate Indicator with Backlight Display

CUB5B000

Optional Plug-in Cards

CUB5RLY

Single Relay Option Card

CUB5RLY0

CUB5SNK

Dual Sinking Open Collector Output card

CUB5SNK0

CUB5COM

RS485 Serial Communications Card

CUB5COM1

RS232 Serial Communications Card

CUB5COM2

CUB5USB

USB Programming Card

CUB5USB0

Accessories

MLPS

+12 VDC Micro-Line Power Supply, 85 to 250 VAC source, 400 mA max out

MLPS1000

+24 VDC Micro-Line Power Supply, 85 to 250 VAC source, 200 mA max out

MLPS2000

CBLPRO

Programming Cable RS232 (RJ11-DB9)

CBLPROG0

CBPRO

Communication Cable RS485 (RJ11-DB9)

CBPRO007

SFCRD

SFCRD200

CBLUSB

USB Programming Cable

CBLUSB00