IIS2DLPCTR datasheet(39/69 Pages) STMICROELECTRONICS

39 / 69 page

DocID031788 Rev 4

39/69

IIS2DLPC

Digital interfaces

6.1.1

I2C operation

The transaction on the bus is started through a START (ST) signal. A START condition is

defined as a high-to-low transition on the data line while the SCL line is held high. After this

has been transmitted by the master, the bus is considered busy. The next byte of data

transmitted after the start condition contains the address of the slave in the first 7 bits and

the eighth bit tells whether the master is receiving data from the slave or transmitting data to

the slave. When an address is sent, each device in the system compares the first seven bits

after a start condition with its address. If they match, the device considers itself addressed

by the master.

The Slave Address (SAD) associated to the IIS2DLPC is 001100xb where the x bit is

modified by the SA0/SDO pin in order to modify the device address. If the SA0/SDO pin is

connected to the supply voltage, the address is 0011001b, otherwise if the SA0/SDO pin is

connected to ground, the address is 0011000b. This solution permits to connect and

address two different accelerometers to the same I2C lines.

Data transfer with acknowledge is mandatory. The transmitter must release the SDA line

during the acknowledge pulse. The receiver must then pull the data line low so that it

remains stable low during the high period of the acknowledge clock pulse. A receiver which

has been addressed is obliged to generate an acknowledge after each byte of data

received.

The I2C embedded inside the IIS2DLPC behaves like a slave device and the following

protocol must be adhered to. After the start condition (ST) a slave address is sent. Once a

slave acknowledge (SAK) has been returned, an 8-bit sub-address (SUB) is transmitted: the

7 LSb represents the actual register address while the CTRL2 (21h) (IF_ADD_INC) bit

defines the address increment.

The slave address is completed with a Read/Write bit. If the bit is ‘1’ (Read), a repeated

START (SR) condition must be issued after the two sub-address bytes. If the bit is ‘0’ (Write)

the master will transmit to the slave with direction unchanged. Table 17 explains how the

SAD+Read/Write bit pattern is composed, listing all the possible configurations.

Table 17. SAD+Read/Write patterns

Command

SAD[6:1]

SAD[0] = SA0

R/W

SAD+R/W

Read

001100

00110001 (31h)

Write

001100

00110000 (30h)

Read

001100

00110011 (33h)

Write

001100

00110010 (32h)

IIS2DLPCTR 数据表(PDF) 39 Page - STMicroelectronics

IIS2DLPCTR 数据表(HTML) 39 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69

数据表下载

链接网址

IIS2DLPCTR 数据表(PDF) 39 Page - STMicroelectronics

IIS2DLPCTR 数据表(HTML) 39 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69

数据表 下载

链接网址

数据表下载