V14

2

SPECIFICATIONS

All Specifications Typical At Nominal Line, Full Load, and 25℃ Unless Otherwise Noted

INPUT SPECIFICATIONS:

ISOLATION VOLTAGE:

Input Voltage Range ....……………..........….......... 24V ......................... 9-36V

500 VDC min. …………………………………………… Standard Models

48V ........................18-72V

3K VDC min. (note4) …………………………………… Suffix “H” Models

Input Filter ………………………………………………….…………..... Pi Type

1.5K VDC min. ….…………………….……………… Suffix “HM” Models

OUTPUT SPECIFICATIONS:

CASE MATERIAL:

Voltage Accuracy ......................................................................... ±2.0% max.

Standard Models …………….…………… Non-Conductive Black Plastic

Voltage Balance (Dual) .................................................................. ±1.0% max.

Suffix “M” Models (note 5) ………... Black Coated Copper with Non-conductive Base

Temperature Coefficient …………………………………………… ±0.05%/℃

NOTE:

Ripple & Noise, 20MHz BW Single & ±5V ………….…… 100mV pk-pk max.

1. Measured from high line to low line.

Dual …..……………………..… 1% pk-pk max.

2. Measured from full load to 10% load.

Short Circuit Protection ……………………………………………… Continuous

3. Measured from full load to 1/4 load.

Line Regulation Single/Dual (note1) …….………………….........…±0.5% max.

4. Non-Conductive black plastic only.

Load Regulation Single (note2) ……………..…….......……….... ±0.5% max.

5. Suffix “S” to the model number with SMD packages.

Dual (note3) ………….…………………………±1.0% max.

6. Maximum case temperature under any operating condition should

GENERAL SPECIFICATIONS:

not be exceeded 95℃(Plastic Case), 100℃(Copper Case).

Efficiency .......................................................................................... See Table

Isolation Resistance .....................................................…… 10

Switching Frequency ................................................................... 100KHz min.

Operating Ambient Temperature Range .................................. -25℃ to +71℃

De-rating, Above 71℃ (Plastic Case) ……… Linearly to Zero power at 95℃

De-rating, Above 71℃ (Copper Case) ….… Linearly to Zero power at 100℃

Case Temperature (Plastic case note6) ...................................... 95℃ max.

(Copper case note6) ……………………….. 100℃ max.

Cooling ………………………………………..…………….. Natural Convection

Storage Temperature Range ………....….......……........ -40℃ to +100℃

Dimensions …… DIP ….….… 1.25x0.80x0.40 inches(31.8x20.3x10.2 mm)

SMD ………… 1.25x0.80x0.45 inches(31.8x20.3x11.4 mm)

Weight …………………………………………………………..………... 12.5g

Case A Dimensions:

BOTTOM

VIEW

SEE NOTE

PIN CONNECTION

500 VDC

1.5K & 3K VDC

Pin

Single Output

Dual Output

1,24

2,23

3,22

10,15

11,14

12,13

+V Input

NC

NC

-V Output

+V Output

-V Input

+V Input

-V Output

-V Input

Common

Common

+V Output

* NP-NO PIN

* NC-NO CONNECTION WITH PIN

All Dimensions In Inches (mm)

Tolerances

Inches: X.XX= ±0.02 , X.XXX= ±0.010

Millimeters: X.X= ±0.5 , X.XX=±0.25

9

4

20,21

CASE AS

TOP

VIEW

DIP

SMD

NP

NC

NP

NC

NP

NC

DIP

SMD

Pin

Single Output

Dual Output

DIP

SMD

DIP

SMD

NP

NC

NP

NC

NP

NC

NC

NC

-V Output

Common

-V Input

-V Input

+V Output

+V Output

Common

-V Output

+V Input

+V Input

1,24

2,3

10,15

11

12,13

14

9

22,23

16

4,5

20,21

NP

NC

NP

NC

NP

NC

NP

NC

NC

NC

NP

NC

NP

NC

NP

NC

NP

NC

16

NP

NC

NP

NC

5

NP

NC

NP

NC

NOTE:Pin Size is 0.02±0.002 Inch (0.5±0.05 mm) DIA

Typical Derating curve for Natural Convection

71

-25

95

100

0%

20%

40%

60%

80%

100%

120%

-25

0

25

50

75

100

Plastic Case

Copper Case