V19

2

Specifications

TR15RAM Series Derating Curve

INPUT SPECIFICATIONS:

Voltage …....………........…........................................... 90~264Vac

Frequency ………………………………………….……………..... 47 to 63Hz

Inrush Current ………………….…………..................... 50A max. @ 240Vac

Leakage Current …………………………………………….…… 0.1mA max.

OUTPUT SPECIFICATIONS:

Hold-up Time …………………………………………… 10ms typ. @115Vac

Temperature Coefficient ...................….........…….....….......…..... ±0.05%/°C

Short Circuit Protection …………….…………… Continuous (Auto Recovery)

Over Voltage Protection …………………………..TVS Component to Clamp

GENERAL CHARACTERISTICS:

NOTE:

Isolation ……………………..……………..……. Input to output = 5,656VDC

1. Add a 0.1uF ceramic capacitor and a 10uF E.L. capacitor to output for

Switching Frequency ………………………………….………… 95KHz typical

Ripple & Noise measuring @20MHz BW.

Operating Temperature .................................. 0 - 70℃(see derating curve)

2. Voltage setpoint at 60% full load.

Storage Temperature ………………...…………...….......……........ -20 - 85℃

3. Line regulation measured from 100Vac to 240Vac full load.

Cooling ………………………………….………………… Natural Convection

4. Load regulation measured from 60% to full load and from 60% to 20%

MTBF ….……… MIL-HDBK-217F, GB, at 25℃/115VAC …… 200Khrs min.

load (60% +/- 40% load).

Humidity .................................................... 93% RH max. Non condensing

5. Typical efficiency at 230VAC and full load at 25℃.

Altitude …………………..……………………………...….…………… 3000m

6. ”Various TR Series adapters are PSE certified. PSE certification alone

Dimensions …..…….. 3.173x1.885x1.704 inches (80.60x47.90x43.30mm)

is not sufficient for importation into Japan. A valid PSE mark must

Weight …………………………………………………… 130g(0.29 Pounds)

contain the name of the importer as shown in the example below. If PSE

SAFETY AND EMC:

mark is required, the name of the registered importer must be supplied

Emission and Immunity (Ed. 4.0) ..... EN55011 Class B, FCC47 CFR Part 15

to Cincon on order placement. Product labels will not contain PSE

EN60601-1-2, EN61000-3-2, 3, IEC61000-4-2, 3, 4, 5, 6, 8, 11

mark if importer name is not supplied. Consult factory or local

Safety (Ed. 3.1) .......................................................… IEC60601-1:2005+A1

representative for details”.

EN60601-1:2006+A11:2011+A1+A12, UL ANSI/AAMI ES60601-1: 2005

Mechanical Specification

3.173[80.60]

70.866[1800.00]±1.969[50.00]

18AWG／1800mm

DC Plug type: V+ ─●)─ V-

DC Plug :Straight(ψ5.5／ψ2.1) L12mm

+

-

Tolerance:Inches:X.XXX±0.02

Millimeters:X.XX±0.5

All Dimensions are in inches[mm]

Typical at 25˚C, nominal line and 75% load, unless otherwise Specified

0%

25%

50%

75%

100%

0

10

20

30

40

50

60

70

20LFM(Natural Convection)