FIBER

SENSORS

LASER

SENSORS

PHOTO-

ELECTRIC

SENSORS

MICRO

PHOTO-

ELECTRIC

SENSORS

AREA

SENSORS

SAFETY LIGHT

CURTAINS /

SAFETY

COMPONENTS

PRESSURE /

FLOW

SENSORS

INDUCTIVE

PROXIMITY

SENSORS

PARTICULAR

USE

SENSORS

SENSOR

OPTIONS

SIMPLE

WIRE-SAVING

UNITS

WIRE-SAVING

SYSTEMS

MEASURE-

MENT

SENSORS

STATIC

CONTROL

DEVICES

LASER

MARKERS

PLC

HUMAN

MACHINE

INTERFACES

ENERGY

MANAGEMENT

SOLUTIONS

FA

COMPONENTS

MACHINE

VISION

SYSTEMS

UV

CURING

SYSTEMS

Selection

Guide

Amplifier

Built-in

Power Supply

Built-in

Amplifier-

separated

EX-Z

CX-400

CY-100

EX-10

EX-20

EX-30

EX-40

CX-440

EQ-30

EQ-500

MQ-W

RX-LS200

RX

RT-610

SENSING CHARACTERISTICS (TYPICAL)

0

···

···

···

These bars indicate the sensing range

with respective objects when the

distance adjuster is set at the sensing

each, with white non-glossy paper.

50

1.969

100

3.937

150

5.906

200

7.874

Wiring

• The output of

RX-LS200-P does not incorporate a short-

circuit protection circuit. Do not connect it directly to a

power supply or a capacitive load.

Others

• Do not use during the initial transient time (50 ms) after

the power supply is switched on.

PRECAUTIONS FOR PROPER USE

Refer to p.1552~ for general precautions.

Mounting

• The tightening torque should be 1.17 N·m or less.

• Care must be taken regarding the sensor mounting

direction with respect to the object’s direction of movement.

Do not make the sensor

detect an object in this

direction because it may

cause unstable operation.

Sensing object

Sensing object

Sensing object

5.5 mm

0.217 in

6 mm

0.236 in

Beam axis

hexagon-socket-head bolt

The sensing axis is

positioned at the

intersection of the “ ”

mark on the lens face

and the “ ” line.

Sensor mounting

bracket

MS-RX-1

(Accessory)

• When detecting a specular object (aluminum or copper

foil) or an object having a glossy surface or coating,

please take care that there are cases when the object

may not be detected due to a small change in angle,

wrinkles on the object surface, etc.

• When a specular body is present below the sensor, use

the sensor by tilting it slightly upwards to avoid wrong

operation.

Use conditions to comply with CE Marking

• Following work must be done in case of using this

product as a CE marking (European standard EMC

Directive) conforming product.

Ensure that the shield is connected to 0 V or the actual

ground.

• In case of connecting a sensor to power supply 0 V by using

a shield (piping, etc.)

• In case of grounding by using a shield (piping, etc.)

Note: The shield (piping, etc.) must be insulated.

Sensor

Shield (piping, etc.)

Power supply

/

Load

+V

0 V

OUT

Sensor

Shield (piping, etc.)

Power supply

/

Load

+V

0 V

OUT

• Never use this product as a sensing device

for personnel protection.

• In case of using sensing devices for

personnel protection, use products which

meet laws and standards, such as OSHA,

ANSI or IEC etc., for personnel protection

applicable in each region or country.

• If a specular body is present in the background, wrong

operation may be caused due to a small change in the

angle of the background body. In that case, install the

sensor at an inclination and confirm the operation with

the actual sensing object.

• Do not install the sensor at a distance of less than 50 mm

in this range.

Correct

Correct

Incorrect