PM-R65W datasheet(4/16 Pages) PANASONIC

4 / 16 page

U-shaped Micro Photoelectric Sensor

PM-25 SERIES PM-45 SERIES PM-65 SERIES

398

FIBER

SENSORS

LASER

SENSORS

PHOTO-

ELECTRIC

SENSORS

MICRO

PHOTO-

ELECTRIC

SENSORS

AREA

SENSORS

SAFETY LIGHT

CURTAINS /

SAFETY

COMPONENTS

PRESSURE /

FLOW

SENSORS

INDUCTIVE

PROXIMITY

SENSORS

PARTICULAR

USE

SENSORS

SENSOR

OPTIONS

SIMPLE

WIRE-SAVING

UNITS

WIRE-SAVING

SYSTEMS

MEASURE-

MENT

SENSORS

STATIC

CONTROL

DEVICES

LASER

MARKERS

PLC

HUMAN

MACHINE

INTERFACES

ENERGY

MANAGEMENT

SOLUTIONS

COMPONENTS

MACHINE

VISION

SYSTEMS

CURING

SYSTEMS

Selection

Guide

U-shaped

Convergent

Reflective

PM-25/PM-45/

PM-65

Ultra-small / Cable type

PM-25 SERIES

SPECIFICATIONS

Type

Ultra-small / Cable type

Bending-resistant cable

3 m 9.843 ft cable

NPN output

PM-□25

PM-□25-R

PM-□25-C3

Item

PNP output

PM-□25-P

―

CE marking directive compliance

EMC Directive, RoHS Directive

Sensing range

6 mm 0.236 in (fixed)

Minimum sensing object

0.8 × 1.2 mm 0.031 × 0.047 in opaque object

Hysteresis

0.05 mm 0.002 in or less

Repeatability

0.01 mm 0.0004 in or less

Supply voltage

5 to 24 V DC ±10 % Ripple P-P 10 % or less

Current consumption

15 mA or less

Output

NPN open-collector transistor

• Maximum sink current: 50 mA

• Applied voltage: 30 V DC or less (between output and 0 V)

• Residual voltage: 2 V or less (at 50 mA sink current)

1 V or less (at 16 mA sink current)

PNP open-collector transistor

• Maximum source current: 50 mA

• Applied voltage: 30 V DC or less (between output and +V)

• Residual voltage: 2 V or less (at 50 mA source current)

1 V or less (at 16 mA source current)

Output operation

Incorporated with 2 outputs: Light-ON/Dark-ON

Short-circuit protection

Incorporated

Response time

Under light received condition: 20 μs or less

Under light interrupted condition: 80 μs or less

(Maximum response frequency: 3 kHz) (Note 2)

Operation indicator

Orange LED (lights up under light received condition)

Pollution degree

Protection

IP64 (IEC)

Ambient temperature

(Note 3, 4)

–25 to +55 °C –13 to +131 °F (No dew condensation or icing allowed), Storage: –30 to +80 °C –22 to +176 °F

Ambient humidity

5 to 85 % RH, Storage: 5 to 95 % RH

Ambient illuminance

Fluorescent light: 1,000 ℓx or less at the light-receiving face

Voltage withstandability

1,000 V AC for one min. between all supply terminals connected together and enclosure

Insulation resistance

20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure

Vibration resistance

10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each

Shock resistance

15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each

Emitting element

Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)

Material

Enclosure: PBT, Display section: Polycarbonate

Cable

0.09 mm2 4-core cabtyre cable, PVC,

1 m 3.281 ft long

0.1 mm2 4-core bending-resistant cabtyre

cable, PVC, 1 m 3.281 ft long (Note 5, 6)

0.09 mm2 4-core cabtyre cable, PVC,

3 m 9.843 ft long

Cable extension

Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note 7)

Weight

Net weight: 10 g approx., Gross weight: 15 g approx.

Net weight: 30 g approx.,

Gross weight: 35 g approx.

Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.

2) The response frequency is the value when the disc, given in the figure below, is rotated.

Disc

1.8 mm 0.071 in

1.6 mm 0.063 in

t = 0.2 mm 0.008 in

1.6 mm 0.063 in

3) In case the

PM-25 series is used at an ambient temperature of +50 °C +122 °F, or more, make sure to mount it on a metal body.

4) Note that the cable of

PM-□25-R loses its flexibility when the ambient temperature decreases to about -10 °C +14 F°.

5) The cable of

PM-□25-R is a bending-resistant cable usable on a moving base. When the sensor is mounted on a moving base, secure the sensor cable

joint at the unit in place so that stress is not applied to it.

6) When storing

PM-□25-R, make sure that the cable does not come into contact with the sensing section or operation indicator.

7) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.

PM-R65W 数据表(PDF) 4 Page - Panasonic Semiconductor

PM-R65W 数据表(HTML) 4 Page - Panasonic Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

数据表下载

链接网址

PM-R65W 数据表(PDF) 4 Page - Panasonic Semiconductor

PM-R65W 数据表(HTML) 4 Page - Panasonic Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

数据表 下载

链接网址

数据表下载