MODEL: DA3

DA3 SPECIFICATIONS

ES-1395 Rev.14 Page 4/7

https://www.m-system.co.jp/

PARAMETER LIST

It is available to configure or confirm settings shown below by using front key pad.

ITEM

MDF.

CODE

DATA

CONTENTS

DEFAULT

P

N/A

-9999 – 9999

(-FFFF – FFFF)

Input display in engineering unit, BCD (as set in ITEM 08/09)

( ) for binary, offset binary, two's complement, re ected binary

–

01

1, 2 , 3

Modi cation code

1 : Data indication only.

2 : All parameters are modi able.

3 : ITEM 22 only.

1

02

N/A

0 – 99

Status indication (“0” is normally indicated.)

0: Normal

1: Memory error

10: Out of input range -15 – 115%

–

03/L

2

-15.0 – 115.0

Input indicated in % (of the range set in ITEM 17/18)

Loop test output with ITEM 01 DATA 2 (‘L’ is indicated as ITEM No.)

–

04

05

2

2

-99.99 – 99.99

-99.99 – 99.99

Zero adjustment (%) ( ne adj. of the value set in ITEM 17)

Span adjustment (%) ( ne adj. of the value set in ITEM 18)

0.00

0.00

06

2

0, 1, 2, 3, 4

Display code

0 : BCD with polarity (decimal)

1 : Binary with polarity

2 : Offset binary

3 : Two’s complement

4 : Re ected binary

0

07

2

0, 1, 2, 3, 4

Available number of bits

0: 16 bits

1: 14 bits

2: 12 bits

3: 10 bits

4: 8 bits

0

08

09

2

2

-9999 – 9999

-9999 – 9999

BCD

Display range scaling

-9999

9999

08

09

2

2

-7FFF – 7FFF

-7FFF – 7FFF

Binary

Display range scaling

-7FFF

7FFF

08

09

2

2

0000 – FFFF

0000 – FFFF

Offset binary

Display range scaling

0000

FFFF

08

09

2

2

8000 – 7FFF

8000 – 7FFF

Two’s complement

Display range scaling

8000

7FFF

08

09

2

2

0000 – FFFF

0000 – FFFF

Re ected binary

Display range scaling

0000

FFFF

10

2

0, 1

0 : Positive

1 : Negative

ITEM 11 and 13 are independent from ITEM 10.

1

11

2

0, 1, 2

LOAD input

2 : Unavailable (unused)

0

12

2

0, 1

POL input

0 : Unavailable (unused)

1 : Available (used)

1

13

2

0, 1

POL input

1

14

2

0, 1, 2

Parity check

0: Disable

1: Enable Parity per each digit

2: Enable Parity for all digits

0

15

2

0, 1

Odd or even parity

0 : Odd

1 : Even

0

16

2

0.0 – 60.0

Delay buffer (seconds, 0 – 90%)

When the Response Time model suffix code is speci ed to 1, the set value is

only effective at 0.5 or higher value.

0.0

17

18

2

2

-1.00 – 1.00

-1.00 – 1.00

Output code V1

-1.00

1.00

17

18

2

2

-10.0 – 10.0

-10.0 – 10.0

Output code V2

-10.0

10.0

17

18

2

2

0.0 – 20.0

0.0 – 20.0

Output code Z1

4.0

20.0

19

2

0 – 99

Power ON-delay time (seconds)

5

20

2

0, 1 – 60

Power-saving mode

0 : Continuous display

1 – 60 : Time before display turned off (minutes)

10

21

2

0 – 9999

Parity check error count

The count value is reset to 0 with double-clicking the DATA DOWN key.

–

22

3

0, 1

Reset all settings

0

23

N/A

—

ROM version

–

*1. ITEM 08 < ITEM 09.

*2. Open collector input logic

LOGIC

ITEM 10

0 : Positive logic

1 : Negative logic

INPUT

DATA

0

1

0

1

TTL level, open collector sink type (TTL level)

Short (LOW)

Open (HIGH)

Open (HIGH)

Short (LOW)

24V DC, open collector source type

Open

Short

Short

Open

*3. “Opencircuit” with 24V DC input

*4. “Shortcircuit” with 24V DC input

*5. Of the range set in ITEM 08/09. ITEM 17 < ITEM 18.