MODEL: JPA

JPA SPECIFICATIONS

ES-1673 Rev.12 Page 2/3

http://www.m-system.co.jp/

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

TERMINAL SCREW MATERIAL

/S01: Stainless steel

RELATED PRODUCTS

• Programming Unit (model: PU-2x)

• PC configurator software (model: JXCON)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

GENERAL SPECIFICATIONS

Construction: Plug-in

Connection: M3.5 screw terminals

Screw terminal: Chromated steel (standard) or stainless

steel

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Overrange output: -10 – +120 % at 1 – 5 V

(0 – 120 % when 0 % input equals to 0 Hz.)

Zero adjustment: -5 to +5 % (front)

Span adjustment: 95 to 105 % (front)

Linearization: 16 points max. represented as percentage of

full-scale

Adjustments: Programming Unit (model: PU-2x); input

range, low-end cutout, zero and span, simulating output,

averaging nonuniform pulses, linearization data, etc.

(Refer to the users manual of JXCON for the adjustments

configurable with JXCON.)

Low-end cutout: 0 – 100 % adjustable (factory set to 0 %);

hysteresis fixed to 1 %

(% of the range from 0 Hz to 100 % frequency.)

INPUT SPECIFICATIONS

Excitation: Shortcircuit protection

Pulse width (time) requirement: 10 msec. min. at

< 20 Hz; duty ratio 20 – 80 % at ≥ 20 Hz

Offset: Max. 3 times span

■ Open Collector

Frequency range: 0 – 0.01 Hz through 25 kHz

(0 – 1 kHz will be used if not otherwise specified)

Sensing: Approx. 12 V DC @ 3 mA

ON/OFF level: ≤ 800 Ω / 2 V for ON,

≥ 1.2 kΩ / 3.6 V for OFF

■ Mechanical Contact

Frequency range: 0 – 0.01 Hz through 5 Hz

(0 – 5 Hz will be used if not otherwise specified)

Sensing: Approx. 12 V DC @ 3 mA

ON/OFF level: ≤ 800 Ω / 2 V for ON,

≥ 1.2 kΩ / 3.6 V for OFF

■ Voltage Pulse: Square or sine waveforms

Frequency range: 0 – 0.01 Hz through 25 kHz

(0 - 1 kHz will be used if not otherwise specified.)

Input amplitude: 2 – 50 Vp-p

Input impedance: 10 kΩ min.

OUTPUT SPECIFICATIONS

■ DC Current: 0 – 20 mA DC

Minimum span: 1 mA

Offset: Max. 1.5 times span

Load resistance: Output drive 15 V max.

■ DC Voltage: -10 – +20 V DC

Span: Min. 5 mV, max. 20 V

Offset: Max. 1.5 times span

Load resistance: Output drive 1 mA max.; at ≥ 0.5 V

INSTALLATION

Power input

•AC: Operational voltage range: rating ±10 %,

50/60 ±2 Hz, approx. 3 VA

•DC: Operational voltage range: rating ±10 %,

ripple 10 %p-p max., approx. 2 W (90 mA at 24 V)

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 350 g (0.77 lb)

PERFORMANCE in percentage of span

Accuracy: ±0.1 % with segment gain ≤ 1 [±0.1 % × gain]

with segment gain > 1

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Response time: 0.5 sec. + 1 pulse cycle (0 – 90 %)

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (input to output

to power to ground)