MODEL: JRP2

JRP2 SPECIFICATIONS

ES-1577 Rev.8 Page 2/5

http://www.m-system.co.jp/

[3] POWER INPUT

AC Power

K: 85 – 132 V AC

DC Power

S: 12 V DC

R: 24 V DC

V: 48 V DC

P: 110 V DC

[4] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

TERMINAL SCREW MATERIAL

/S01: Stainless steel

RELATED PRODUCTS

• Programming Unit (model: PU-2x)

• PC configurator software (model: JXCON)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

GENERAL SPECIFICATIONS

Construction: Plug-in

Connection: M3.5 screw terminals

Screw terminal: Chromated steel (standard) or stainless

steel

Housing material: Flame-resistant resin (black)

Isolation: Input to DC output to alarm output to power

Overrange output: Approx. -15 to +115 % at 1 – 5 V

Zero adjustment: -5 to +5 % (front)

Span adjustment: 95 to 105 % (front)

Alarm mode: High or Low

Alarm setpoint: -15 – +115 %

Alarm deadband: 0 – 20 %

Input monitor (PL1): Red LED blinks according to the input

phase A.

Input monitor (PL2): Red LED blinks according to the input

phase B.

Excitation adjustment: 5 – 24 V DC

Software programming: Programming Unit (model: PU-2x);

(Refer to the users manual of JXCON for the adjustments

configurable with JXCON)

• Input frequency range

• Zero and span

• Low-end cutout

• Alarm setpoint

• Output fine adjustment

• Linearrization

• Others

Adjustments: With DIP and Rotary switches.

• Input Type

• Noise Filter

• Pulse amplitude

(Refer to the instruction manual for details)

Modular jack: Connecting the PU-2x

Low-end cutout: Specify frequency (When the low-end

cutout is set to 0 Hz, the deadband is not valid.)

INPUT SPECIFICATIONS

Excitation: Shortcircuit protection; approx. 440 mA (max.) at

shortcircuit

Maximum frequency: 200 kHz

Frequency ranges: 0 – 0.01 Hz through 100 kHz

Note: Choose 100 kHz range to set the zero/span

frequencies greater than 100 kHz.

Minimum span: 10 % of the selected frequency range

Minimum pulse width time requirement: 2.5 μsec. for both

ON and OFF

■ Open Collector

Input requirements (Excitation: Sensing)

5 V: Approx. 4 V / 1.0 mA

12 V: Approx. 9 V / 2.3 mA

24 V: Approx. 16 V / 4.7 mA

ON resistance: ≤ 200 Ω

OFF resistance: ≥ 200 kΩ

Detecting level:

1 V (5 V excitation)

2 V (12/24 V excitation)

(Detecting voltage in the internal circuit. For open collector

input, be sure to re-adjust the voltage back to 1 V (5 V

excitation) or 2 V (12/24 V excitation) if it has been changed

for other input types.)

Detecting pulse edge: OFF (input monitor LED ON) to ON

(LED OFF)

■ Voltage Pulse

Waveform: Square or sine

Input impedance: 10 kΩ min.

Pulse amplitude: 0.1 – 100 Vp-p

Max. voltage between input terminals: 50 V

Detecting level: 0 – 5 V (factory setting: 2 V)

(Detecting voltage in the internal circuit.)

Detecting pulse state: A pulse rise detected when the input

voltage goes above the detecting level (input monitor LED