MODEL: JARP2

JARP2 SPECIFICATIONS

ES-1570 Rev.6 Page 1/4

http://www.m-system.co.jp/

Plug-in Signal Conditioners M-UNIT

DC/2-PHASE PULSE CONVERTER

(field-programmable)

Functions & Features

• Providing pulse rate outputs in 90-degree phase angle in

proportion to DC input signal

• Parameters are field-programmable via hand-held

programmer PU-2x

• Isolation up to 2000 V AC

• High-density mounting

Typical Applications

• Remote transmission of rotary encoder signal via 4 – 20

mA cable in combination with the JRP2

50

(1.97)

136

(5.35)

80

(3.15)

mm (inch)

MODEL: JARP2–[1][2]–[3][4]

ORDERING INFORMATION

• Code number: JARP2–[1][2]–[3][4]

Specify a code from below for each of [1] through [4].

(e.g. JARP2-6A-S/Q)

• Special input range (For codes Z & 0)

• Use Ordering Information Sheet (No. ESU-1570). Default

setting (table below) will be used if not otherwise specified.

• Specify the specification for option code /Q

(e.g. /C01/S01)

DEFAULT

ITEM

Output zero frequency

Output span frequency

Alarm setpoint

Alarm hysteresis

3.0 sec.

Alarm mode

No alarm

-1 kHz

100.00%

Power ON-delay time

1.00%

1 kHz

[1] INPUT

Current

A: 4 – 20 mA DC (Input resistance 250 Ω)

A1: 4 – 20 mA DC (Input resistance 50 Ω)

B: 2 – 10 mA DC (Input resistance 500 Ω)

C: 1 – 5 mA DC (Input resistance 1000 Ω)

D: 0 – 20 mA DC (Input resistance 50 Ω)

E: 0 – 16 mA DC (Input resistance 62.5 Ω)

F: 0 – 10 mA DC (Input resistance 100 Ω)

G: 0 – 1 mA DC (Input resistance 1000 Ω)

H: 10 – 50 mA DC (Input resistance 100 Ω)

Z: Specify current (See INPUT SPECIFICATIONS)

Voltage

1: 0 – 10 mV DC (Input resistance 10 kΩ min.)

2: 0 – 100 mV DC (Input resistance 100 kΩ min.)

3: 0 – 1 V DC (Input resistance 1 MΩ min.)

4: 0 – 10 V DC (Input resistance 1 MΩ min.)

5: 0 – 5 V DC (Input resistance 1 MΩ min.)

6: 1 – 5 V DC (Input resistance 1 MΩ min.)

4W: -10 – +10 V DC (Input resistance 1 MΩ min.)

0: Specify voltage (See INPUT SPECIFICATIONS)

[2] OUTPUT

A: Open collector

M: 5 V pulse

N: 12 V pulse

P: 24 V pulse

J: RS-422 line driver pulse

[3] POWER INPUT

AC Power

M2: 100 – 240 V AC

DC Power

S: 12 V DC

R: 24 V DC

P: 110 V DC

[4] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

TERMINAL SCREW MATERIAL

/S01: Stainless steel

RELATED PRODUCTS

• Programming Unit (model: PU-2x)

• PC configurator software (model: JXCON)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the