MODEL: JARP2

JARP2 SPECIFICATIONS

ES-1570 Rev.6 Page 2/4

http://www.m-system.co.jp/

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

GENERAL SPECIFICATIONS

Construction: Plug-in

Connection: M3.5 screw terminals

Screw terminal: Chromated steel (standard) or stainless

steel

Housing material: Flame-resistant resin (black)

Isolation: Input to alarm output to output to power

Zero adjustment: -5 to +5 % (front)

Span adjustment: 95 to 105 % (front)

Alarm output: Turns on when the input goes above (high) or

below (low) setpoint

Alarm setpoint: -5 – +105 %

Alarm deadband (hysteresis): 0 – 20 %

Output monitor LED: Red LED turns on according to the

output (phase A and B).

Power ON delay time: 2.0 to 1000.0 sec.

Software programming: Programming Unit (model: PU-2x);

(Refer to the users manual of JXCON for the adjustments

configurable with JXCON)

• Output frequency (zero and span)

• Alarm

• Power ON delay time

• Others

INPUT SPECIFICATIONS

■ DC Current:

Shunt resistor attached to the input terminals (0.5 W)

Specify input resistance value for code Z.

■ DC Voltage: -300 – +300 V DC

Minimum span: 10 mV

Offset: Max. 1.5 times span

Input resistance

Span 10 – 100 mV : ≥ 10 kΩ

Span 0.1 – 1 V : ≥ 100 kΩ

Span ≥ 1 V : ≥ 1 MΩ

OUTPUT SPECIFICATIONS

Phase angle: ±90°

Forward (positive output): Phase A = Phase B + 90°

Reverse (negative output): Phase A = Phase B – 90°

Frequency range: 100 mHz to 10 kHz (RNG1 to RNG6)

[ Range name : Available frequency ]

RNG1 10 kHz: -20 – +20 kHz

RNG2 1 kHz: -2 – +2 kHz

RNG3 100 Hz: -200 – +200 Hz

RNG4 10 Hz: -20 – +20 Hz

RNG5 1 Hz: -2 – +2 Hz

RNG6 100 mHz: -200 – +200 mHz

Min. span: 10 % of available frequency range

Duty ratio: 50 %

■ Open Collector: 50 V DC @50 mA (resistive load)

Saturation voltage: 0.6 V DC

■ Voltage Pulse

H level: Rating 5, 12 or 24 V ±10 %

L level: ≤ 0.5 V

Load resistance: ≥ 1 kΩ (5 V), ≥ 2.4 kΩ (12 V), ≥ 4.8 kΩ (24

V)

■ RS-422 Line Driver Pulse

Transmitter: Conforms to RS-422

■ Relay Contact:

100 V AC @ 1 A (cos ø = 1)

120 V AC @ 1 A (cos ø = 1)

240 V AC @ 0.5 A (cos ø = 1)

30 V DC @ 1 A (resistive load)

Maximum switching voltage: 380 V AC or 125 V DC

Maximum switching power: 120 VA or 30 W

Minimum load: 5 V DC @ 10 mA

INSTALLATION

Power input

•AC: Operational voltage range 85 – 264 V, 47 - 66 Hz;

Approx. 4.1 VA at 100 V

Approx. 5.9 VA at 200 V

Approx. 7.7 VA at 264 V

•DC: Operational voltage range: rating ±10 %, or 85 – 150 V

for 110 V rating (ripple 10 % p-p max.)

Approx. 2.8 W (120 mA at 24 V)

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 280 g (0.62 lb)

PERFORMANCE in percentage of span

Accuracy

Output 10 kHz range: ±0.3 %

Output ≤ 1 kHz range: ±0.1 %

Alarm setpoint accuracy: ±0.1 %

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Response time: 0.3 sec. + (one cycle at 100 % output)

Time required from a step input (0 – 100 %) to the first

pulse output.

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @ 1 minute (input to alarm

output to output to power to ground)