MODEL: KAPU

KAPU SPECIFICATIONS

ES-3582 Rev.13 Page 2/5

http://www.m-system.co.jp/

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Zero adjustment: 0 – 5 % (front)

Span adjustment: 50 – 100 % of range (front)

Output frequency adjustment: Preselecting range

with a rotary switch and fine control

with span adjustment (50 – 100 %)

Output pulse width adjustment:Three-turn screwdriver

adjustment (front)

Low-end cutout: 0 to 10 % (front); a red LED assists in

adjusting the cutout point; turns on during the cutout.

INPUT SPECIFICATIONS

■ DC Current:

Shunt resistor attached to the input terminals (0.5 W)

Specify input resistance value for code Z.

■ DC Voltage: -300 – +300 V DC

Minimum span: 10 mV

Offset: Max. 1.5 times span

Input resistance

Span 10 – 100 mV : ≥ 10 kΩ

Span 0.1 – 1 V : ≥ 100 kΩ

Span ≥ 1 V : ≥ 1 MΩ

OUTPUT SPECIFICATIONS

Note: For factory setting, maximum frequency of the

selected range is used to determine pulse width. Pulse

width is adjusted until the duty ratio becomes 50 % of the

maximum frequency. If this value lies outside of the

adjustable range, either maximum or minimum selectable

value will be used.

■ Open Collector:

50 V DC @ 50 mA (resistive load)

Frequency range: 0 – 10 kHz

ON pulse width: 40 μsec. – 0.8 msec. adjustable

Saturation voltage: 0.6 V DC

■ Low Frequency Open Collector:

50 V DC @ 50 mA (resistive load)

Frequency range: 0 – 130 pulses/min.

ON pulse width: 40 msec. – 0.8 sec. adjustable

Saturation voltage: 0.6 V DC

■ Middle Range Frequency Open Collector:

50 V DC @ 50 mA (resistive load)

Frequency range: 0 – 312 Hz

ON pulse width: 2 – 35 msec. adjustable

Saturation voltage: 0.6 V DC

■ Relay Contact: 120 V AC @ 200 mA (cos ø = 1)

240 V AC @ 100 mA (cos ø = 1)

24 V DC @ 200 mA (resistive load)

Maximum switching voltage: 380 V AC or 125V DC

Maximum switching power: 24 VA or 4.8 W

Minimum load: 5 V DC @ 10 mA

Frequency range: 0 – 130 pulses/min.

ON pulse width: 40 msec. – 0.8 sec. adjustable

Relay life:

■ 5 V Pulse

Frequency range: 0 – 10 kHz

Low pulse width: 40 μsec. – 0.8 msec. adjustable

High level: 5 V ± 10 %

Low level: ≤ 0.5 V

Load resistance: 600 Ω min.

■ Middle Range Frequency 5 V Pulse

Frequency range: 0 – 312 Hz

Low pulse width: 2 – 35 msec. adjustable

High level: 5 V ±10 %

Low level: ≤0.5 V

Load resistance: 600 Ω min.

■ Low Frequency 5 V Pulse

Frequency range: 0 – 130 pulses/min.

Low pulse width: 40 msec. – 0.8 sec. adjustable

High level: 5 V ± 10 %

Low level: ≤ 0.5 V

Load resistance: 600 Ω min.

■ 24 V Pulse

Frequency range: 0 – 130 pulses/min.

High pulse width: 40 msec. – 0.8 sec. adjustable

High level: 24 V ±10%

Low level: ≤ 0.5 V

Load current: 30 mA max.

Load resistance: 800 Ω min.

SW No.

SPAN RANGE

MIN. (50%)

MAX. (100%)

0

1

2

0 – 5 kHz

0 – 2.5 kHz

0 – 1.25 kHz

0 – 10 kHz

0 – 5 kHz

0 – 2.5 kHz

•

Open Collector, 5V Pulse

3

4

5

0 – 625 Hz

0 – 312 Hz

0 – 156 Hz

0 – 1.25 kHz

0 – 625 Hz

0 – 312 Hz

6

7

8

0 – 78 Hz

0 – 39 Hz

0 – 20 Hz

0 – 156 Hz

0 – 78 Hz

0 – 39 Hz

9

A

B

0 – 10 Hz

0 – 5 Hz

0 – 2.5 Hz

0 – 20 Hz

0 – 10 Hz

0 – 5 Hz

C

D

E

0 – 1.25 Hz

0 – 36 pulses/min.

0 – 18 pulses/min.

0 – 2.5 Hz

0 – 1.25 Hz

0 – 36 pulses/min.

F

0 – 9 pulses/min.

0 – 18 pulses/min.