MODEL: M2PHS2

M2PHS2 SPECIFICATIONS

ES-5105 Rev.8 Page 1/5

http://www.m-system.co.jp/

Super-mini Signal Conditioners Mini-M Series

PEAK HOLD

(with simple loop test output)

Functions & Features

• Track mode: the output follows proportionally to the input

• Peak-hold mode: responds only to an increasing signal,

holding the maximum value until a higher signal or a

command to reset is received

• Valley hold and peak-to-peak mode selectable

• Simple loop test output (0, 50, 100%)

Typical Applications

• Monitoring peak power consumption

• Monitoring the highest or lowest temperature

Model

SPAN

ZERO

23 (.91)

76

(2.99)

124

(4.88)

mm (inch)

MODEL: M2PHS2[1]-[2][3]-[4][5]

ORDERING INFORMATION

• Code number: M2PHS2[1]-[2][3]-[4][5]

Specify a code from below for each of [1] through [5].

(e.g. M2PHS2H-6A-M2/CE/Q)

• Special input and output ranges (For codes Z & 0)

• Specify the specification for option code /Q

(e.g. /C01/S01)

[1] HOLD FUNCTION

H: Peak hold

L: Valley hold

W: Peak-to-peak hold

[2] INPUT

Current

A: 4 – 20 mA DC (Input resistance 250 Ω)

A1: 4 – 20 mA DC (Input resistance 50 Ω)

B: 2 – 10 mA DC (Input resistance 500 Ω)

C: 1 – 5 mA DC (Input resistance 1000 Ω)

D: 0 – 20 mA DC (Input resistance 50 Ω)

E: 0 – 16 mA DC (Input resistance 62.5 Ω)

F: 0 – 10 mA DC (Input resistance 100 Ω)

G: 0 – 1 mA DC (Input resistance 1000 Ω)

H: 10 – 50 mA DC (Input resistance 100 Ω)

J: 0 – 10 μA DC (Input resistance 1000 Ω)

K: 0 – 100 μA DC (Input resistance 1000 Ω)

GW: -1 – +1 mA DC (Input resistance 1000 Ω)

FW: -10 – +10 mA DC (Input resistance 100 Ω)

Z: Specify current (See INPUT SPECIFICATIONS)

Voltage

1: 0 – 10 mV DC (Input resistance 10 kΩ min.)

15: 0 – 50 mV DC (Input resistance 10 kΩ min.)

16: 0 – 60 mV DC (Input resistance 10 kΩ min.)

2: 0 – 100 mV DC (Input resistance 100 kΩ min.)

3: 0 – 1 V DC (Input resistance 1 MΩ min.)

4: 0 – 10 V DC (Input resistance 1 MΩ min.)

5: 0 – 5 V DC (Input resistance 1 MΩ min.)

6: 1 – 5 V DC (Input resistance 1 MΩ min.)

4W: -10 – +10 V DC (Input resistance 1 MΩ min.)

5W: -5 – +5 V DC (Input resistance 1 MΩ min.)

0: Specify voltage (See INPUT SPECIFICATIONS)

[3] OUTPUT

Current

A: 4 – 20 mA DC (Load resistance 750 Ω max.)

B: 2 – 10 mA DC (Load resistance 1500 Ω max.)

C: 1 – 5 mA DC (Load resistance 3000 Ω max.)

D: 0 – 20 mA DC (Load resistance 750 Ω max.)

E: 0 – 16 mA DC (Load resistance 900 Ω max.)

F: 0 – 10 mA DC (Load resistance 1500 Ω max.)

G: 0 – 1 mA DC (Load resistance 15 kΩ max.)

Z: Specify current (See OUTPUT SPECIFICATIONS)

Voltage

1: 0 – 10 mV DC (Load resistance 10 kΩ min.)

2: 0 – 100 mV DC (Load resistance 100 kΩ min.)

3: 0 – 1 V DC (Load resistance 1000 Ω min.)

4: 0 – 10 V DC (Load resistance 10 kΩ min.)

5: 0 – 5 V DC (Load resistance 5000 Ω min.)

6: 1 – 5 V DC (Load resistance 5000 Ω min.)

4W: -10 – +10 V DC (Load resistance 10 kΩ min.)

5W: -5 – +5 V DC (Load resistance 5000 Ω min.)

0: Specify voltage (See OUTPUT SPECIFICATIONS)

[4] POWER INPUT

AC Power

M: 85 – 264 V AC (Operational voltage range 85 – 264 V,

47 – 66 Hz)

(Select ‘/N’ for ‘Standards & Approvals’ code.)

M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,

47 – 66 Hz)

DC Power

R: 24 V DC