MODEL: M2XRP2

http://www.m-system.co.jp/

M2XRP2 SPECIFICATIONS

ES-5059 Rev.12 Page 2/6

[5] OPTIONS (multiple selections)

Standards & Approvals (must be specified)

/N: Without CE or UL

/CE: CE marking

/UL: UL approval, CE marking

Other Options

blank: none

/Q: Option other than the above (specify the specification)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating (UL not available)

TERMINAL SCREW MATERIAL

/S01: Stainless steel (UL not available)

RELATED PRODUCTS

• PC configurator software (model: JXCON)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

GENERAL SPECIFICATIONS

Construction: Plug-in

Connection: M3 screw terminals (torque 0.8 N·m)

Screw terminal: Chromated steel (standard) or stainless

steel

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Overrange output: Approx. -15 to +115 % at 1 – 5 V

Zero adjustment: -5 to +5 % (front)

Span adjustment: 95 to 105 % (front)

Configuration: Via PC Configurator Software (model:JXCON)

on the Windows PC connected to

the front jack.

Programmable features include:

· I/O type and range

· Zero and span adjustments

· Low-end cutout

· Linearization

Status indicator LED: Red LED; Flashing patterns indicate

different operating status of the transmitter.

Input monitor (PL1): Green LED blinks according to the input

phase A.

Input monitor (PL2): Green LED blinks according to the input

phase B.

Excitation adjustment: 5V or 12V DC

Configurator connection: 2.5 dia. miniature jack;

RS-232-C level

Pulse sensing: DC coupled or capacitor coupled selectable

with DIP SW

Low-end cutout: 100 msec. – 100 sec. or no cutout

programmable

INPUT SPECIFICATIONS

Excitation: Shortcircuit protection; 20 mA max. at

shortcircuit

Maximum frequency: 200 kHz

Frequency ranges:

0 – 10 mHz, 0 – 100 mHz, 0 – 1 Hz, 0 – 10 Hz, 0 – 100 Hz,

0 – 1 kHz, 0 – 10 kHz, 0 – 100 kHz

(Choose 100 kHz range to set the zero/span frequencies

lower than -100 kHz (higher than 100 kHz in the reverse

direction) or higher than 100 kHz (higher than 100 kHz in

the forward direction.))

Minimum pulse width time requirement: 2.5 μsec.

Minimum span: 10 % of the selected frequency range

Noise filter: See table 2

■ Open Collector

Input requirements

EXCITATION

SENSING

OFF

ON

5 V

Approx. 5 V

≥200 kΩ

≤200 Ω

12 V

Approx. 10 V

≥200 kΩ

≤200 Ω

Amplitude: 5 - 12 V

Detecting level:

5 V excitation: 1 V

12 V excitation: 2 V

(Detecting voltage in the internal circuit.

For open collector input, be sure to re-adjust the voltage

back to 1 V (5 V excitation) or 2 V (12 V excitation) if it has

been changed for other input types.)

Detecting pulse edge: OFF to ON

If not specified, the input range is 0 Hz – 1 kHz.

■ Voltage Pulse

Waveform: Square or sine

Input impedance: 10 kΩ min.

Pulse amplitude: 0.1 – 30 Vp-p

Pulse amplitude Range: See table 1.

Max. voltage between input terminals: See table 1.

Sensitivity Scale: See table 1.

Detecting level: -2 – +4 V

Detecting pulse state: A pulse rise detected when the input

voltage goes above the detecting level;

a pulse sink detected when it goes below the level.

If not specified, the input range is 0 Hz – 1 kHz.

■ RS-422 Line Driver Pulse

Receiver: Conforms to RS-422

If not specified, the input range is 0 Hz – 1 kHz.