MODEL: M2SP

M2SP SPECIFICATIONS

ES-5056 Rev.20 Page 2/3

http://www.m-system.co.jp/

GENERAL SPECIFICATIONS

Construction: Plug-in

Connection: M3 screw terminals (torque 0.8 N·m)

Screw terminal: Chromated steel (standard) or stainless

steel

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Overrange output: 0 to 120 % at 1 – 5 V

Zero adjustment: -5 to +5 % (front)

Span adjustment: 95 to 105 % (front)

Input pulse sensing: DC coupled; detecting pulse rise

Input filter: Provided with input range < 100 Hz

(time constant approx. 1 msec.)

Low-end cutout: 2 to 5 %

(For /DN option, the output signal may fluctuate when the

input signal is less than 5 %.)

INPUT SPECIFICATIONS

Excitation: 12 V DC @30 mA; shortcircuit protection

Frequency range: 0 – 50 Hz through 10 kHz

■ Dry Contact: Mechanical contact or open collector

Pulse width time requirement: 20 μsec. min. for ON and OFF

≥ 5 msec. with input range < 100 Hz

Sensing: Approx. 12 V DC @3 mA

ON/OFF level: ≤ 200 Ω / 0.6 V for ON, ≥ 100 kΩ / 2.5 V for

OFF

■ Voltage Pulse: Square or sine waveforms

Pulse width time requirement: 20 μsec. min. for high and

low levels

≥ 5 msec. with input range < 100 Hz

Hi level: 2 – 50 V

Lo level: ≤ 1 V

Input impedance: 10 kΩ min.

OUTPUT SPECIFICATIONS

■ DC Current: 0 – 20 mA DC

Minimum span: 1 mA

Offset: Max. 1.5 times span

Load resistance: Output drive 15 V max.

■ DC Voltage: 0 – 12 V DC

Minimum span: 5 mV

Offset: Max. 1.5 times span

Load resistance: Output drive 1 mA max.; at ≥ 0.5 V

INSTALLATION

Power Consumption

•AC:

Approx. 4 VA at 100 V

Approx. 5 VA at 200 V

Approx. 6 VA at 264 V

•DC: Approx. 3 W

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 150 g (0.33 lb)

PERFORMANCE in percentage of span

Accuracy: ±0.1 % (output 10 – 100 %)

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Response time: (0 – 90%)

Approx. 1.8 sec. with 0 – 50 Hz

Approx. 0.7 sec. with 0 – 100 Hz

Approx. 0.5 sec. with 0 – 500 Hz

Approx. 0.5 sec. with 0 – 10 kHz

Ripple: 0.2 %p-p max. with input ≥ 10 %

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (input to output

to power to ground)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1

Installation Category II

Pollution Degree 2

Input or output to power: Reinforced insulation (300 V)

Input to output: Basic insulation (300 V)

RoHS Directive

EN 50581

Approval:

UL/C-UL nonincendive Class I, Division 2,

Groups A, B, C, and D

(ANSI/ISA-12.12.01, CAN/CSA-C22.2 No.213)

UL/C-UL general safety requirements

(UL 61010-1, CAN/CSA-C22.2 No.61010-1)