MODEL: M6NXAR

M6NXAR SPECIFICATIONS

ES-7923 Rev.4 Page 1/4

http://www.m-system.co.jp/

Screw Terminal Ultra-Slim Signal Conditioners M6N Series

RTD ALARM

(PC programmable)

Functions & Features

• 7.5-mm wide ultra-slim design

• Low profile allows the M6N module mounted in a 120-mm

deep panel

• PC programmable

• Linearization and upscale and downscale burnout

protection

• High-density mounting

• Power and status indicator LEDs

mm (inch)

7.5 (.30)

102

(4.02)

102

(4.02)

MODEL: M6NXAR–[1]–R[2]

ORDERING INFORMATION

• Code number: M6NXAR-[1]-R[2]

Specify a code from below for each [1] and [2].

(e.g. M6NXAR-4-R/Q)

• Temperature range (e.g. 0 – 100°C)

• Specify the specification for option code /Q

(e.g. /C01)

[1] INPUT RTD

1: JPt 100 (JIS'89)

(Usable range: -200 to +500°C, -328 to +932°F)

3: Pt 100 (JIS'89)

(Usable range: -200 to +650°C, -328 to +1202°F)

4: Pt 100 (JIS'97, IEC)

(Usable range: -200 to +850°C, -328 to +1562°F)

5: Pt 50 Ω (JIS'81)

(Usable range: -200 to +649 °C, -328 to +1200°F)

7: Pt 1000

(Usable range: -200 to +850°C, -328 to +1562°F)

9: Cu 10 @25°C

(Usable range: -50 to +250°C, -58 to +482°F)

0: Specify (Please provide a resistance table.)

(Configurator software is used to change the input type and

range. Input code 7: Pt 1000 cannot be switched to/from

other input types while its temperature range can be

changed.)

OUTPUT

Relay; SPDT or transfer contact

POWER INPUT

DC Power

R: 24 V DC

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

[2] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

RELATED PRODUCTS

• PC configurator software (model: M6CFG)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

GENERAL SPECIFICATIONS

Connection

Input and output: M3 screw terminal (torque 0.5 N·m)

Power input: Via the Installation Base (model: M6NBS)

or M3 screw terminal (torque 0.5 N·m)

Recommended solderless terminal: Max. 5.8 mm (0.23”)

wide; Ones with insulation sleeve do not fit.

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Burnout: Upscale standard; downscale or no burnout

optional by programming

In case of upscale standard, the alarm operates as if the

input signal has exceeded over the range.

Linearization: Standard

Power LED: Green light turns on when the power is supplied.

Status indicator LED: Orange LED; Blinking patterns indicate

different operating status of the transmitter.

Alarm monitor LED: Red LED turns on when the alarm is