MODEL: WJPAD2

WJPAD2 SPECIFICATIONS

ES-2275 Rev.2 Page 2/5

http://www.m-system.co.jp/

[3] OUTPUT 2

Current

A: 4 – 20 mA DC (Load resistance 350 Ω max.)

B: 2 – 10 mA DC (Load resistance 700 Ω max.)

C: 1 – 5 mA DC (Load resistance 1400 Ω max.)

D: 0 – 20 mA DC (Load resistance 350 Ω max.)

E: 0 – 16 mA DC(Load resistance 430 Ω max.)

F: 0 – 10 mA DC (Load resistance 700 Ω max.)

G: 0 – 1 mA DC (Load resistance 7000 Ω max.)

Z: Specify current (See OUTPUT SPECIFICATIONS)*

Voltage

Same range availability as Output 1

* For specify voltage and current, specify same code and

output to output 1 and output 2. Consult M-System when

different output codes are combined and specified.

[4] POWER INPUT

AC Power

K: 85 – 132 V AC

DC Power

S: 12 V DC (under development)

R: 24 V DC

V: 48 V DC

P: 110 V DC

[5] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

TERMINAL SCREW MATERIAL

/S01: Stainless steel

RELATED PRODUCTS

• Programming Unit (model: PU-2x)

• PC configurator software (model: JXCON)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

GENERAL SPECIFICATIONS

Construction: Plug-in

Connection: M3.5 screw terminals

Screw terminal: Chromated steel (standard) or stainless

steel

Housing material: Flame-resistant resin (black)

Isolation: Input or alarm output to output 1 to output 2 to

power

Overrange output: Approx. -15 to +115 % at 1 – 5 V

Zero adjustment: -5 to +5 % (front)

Span adjustment: 95 to 105 % (front)

Adjustable individually for each output 1 and output 2.

Alarm mode: High or Low

Alarm setpoint: -15 – +115 %

Alarm deadband: 0 – 20 %

Linearization: Max. 16 points

Input monitor LED: Red LED blinks according to the input.

Excitation adjustment: 5 – 24 V DC

Software programming: Programming Unit (model: PU-2x);

(Refer to the users manual of JXCON for the adjustments

configurable with JXCON)

• Input frequency range

• Zero and span

• Low-end cutout

• Linearization

• Alarm setpoint

• Output fine adjustment

• Averaging non-uniform pulses

• Others

Adjustments: With DIP and Rotary switches.

• Input Type

• Pulse Sensing

• Noise Filter

• Detecting level

(Refer to the instruction manual for details)

Modular jack: Connecting the PU-2x

Low-end cutout: -15 – +115 % adjustable

(% of the input range determined by the input zero and

span frequencies. This unit outputs 0 % for the input below

the setting. When the input zero frequency is set to 0 Hz,

the low-end cutout setting below 0 % is not valid.)

INPUT SPECIFICATIONS

Excitation: Shortcircuit protection; approx. 300 mA at

shortcircuit

Frequency ranges: 0 – 0.01 Hz through 100 kHz (up to 10 Hz

for mechanical contact)

Minimum pulse width time requirement: 5 μsec.; 50 msec.

for mechanical contact (for both ON and OFF)

Minimum span: 10 % of the selected frequency range

■ Open Collector & Mechanical Contact

Input requirements

(Excitation: Sensing: OFF: ON)

5 V: Approx. 4 V / 1.0 mA: ≥ 200 kΩ: ≤ 200 Ω

12 V: Approx. 9 V / 2.3 mA: ≥ 200 kΩ: ≤ 200 Ω