MODEL: 10BXC

http://www.m-system.co.jp/

10BXC SPECIFICATIONS

ES-0893 Rev.12 Page 1/7

High-density Signal Conditioners 10-RACK

STANDARD RACK

Functions & Features

• Standard 19" rack for 10-RACK signal conditioners

• Line power supplied via the rear rack bus

• Dual-redundant power supply or two independent power

sources selectable with AC power supply

• Supply pressure at manifold plug

• Direct interface to various DCS with the rack connector

MODEL: 10BXC-[1][2]-[3][4]

ORDERING INFORMATION

• Code number: 10BXC-[1][2]-[3][4]

Specify a code from below for each [1] through [4].

(e.g. 10BXC-12-K2/Q)

• Specify the specification for option code /Q

(e.g. /C01)

[1] FUNCTION

1: Power distribution

2: Power distribution & pressure supply

[2] CONNECTOR

0: None

1: Fujitsu FCN type I/O connector

2: Yokogawa DCS connector (MAC2 dual redundant system use)

3: Nippon Shokubai DCS connector

4: Azbil DCS AI connector

5: Azbil DCS AO connector

6: Azbil DCS AI connector (ELCO connector)

7: Azbil DCS AO connector (ELCO connector)

8: Yokogawa DCS connector (VMx/PM1 dual redundant system use)

E3: Toshiba DCS SAIN1 card use

(Panasonic AXM220001 used)

(DISCONTINUED; replace with code "E3A".)

E3A: Toshiba DCS SAIN1 card supported

(Omron XG4A-2031 used)

H1: Hitachi DCS connector

H2: Hitachi DCS EX-CDL cable connector

M-System guarantees the connecting section.

[3] POWER SUPPLY UNIT

AC Power

K: 85 – 132 V AC; single power source

(Operational voltage range 85 – 132 V, 47 – 63 Hz)

K2: 85 – 132 V AC; dual-redundant power supply

(Operational voltage range 85 – 132 V, 47 – 63 Hz)

KK: 85 – 132 V AC; two independent power sources

(Operational voltage range 85 – 132 V, 47 – 63 Hz)

L: 170 – 264 V AC; single power source

(Operational voltage range 170 – 264 V, 47 – 63 Hz)

L2: 170 – 264 V AC; dual-redundant power supply

(Operational voltage range 170 – 264 V, 47 - 63 Hz)

DC Power

R: 24 V DC; no power supply unit

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

AC/DC Power

KR: 85 – 132 V AC / 24 V DC; two independent power sources

(85 – 132 V, 47 – 63 Hz or 24V ±10 %, ripple 10 %p-p max.)

(Redundant or independent power sources are

recommended for long time use without interruption.)

[4] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

Power supply and signal conditioner side of the main PWB are not coated.

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

RELATED PRODUCTS

• Blank filler plate (model: P-101)

• Connector terminal block (model: CNT)

• Special cable with 40-pin connector (model: FCN)

GENERAL SPECIFICATIONS

Construction: Metal plates assembly

Capacity: 16 positions

Connection

Power input: M4 screw terminals (torque 0.8 N·m)

Power alarm: M4 screw terminals (torque 0.8 N·m)

Pneumatic: Rc 3/8" female (torque ≤ 12 N·m)

Screw terminal: Nickel-plated brass

Manifold: Aluminium alloy

Isolation: I/O connector to alarm output to power to FG

Power alarm output: N.C. contact turns off at power failure

or failure of power units. Supplied only with dual-redundant

power supply or two independent power sources