MODEL: 18BXE

http://www.m-system.co.jp/

18BXE SPECIFICATIONS

ES-1806 Rev.9 Page 5/6

18-RACK LOCATION NO.

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16

AZBIL DCS AO CONNECTOR

•Azbil DCS AO connector

I/O cable

: J-RSL / J-RSK

J-RRL / J-RRK

Location

Output connector

: 57GE-40500-751

CN1, CN2

: J-AOM10 module use

The input is connected to the connector. The CN1 and

CN2 are connected in parallel.

Install the Extender Module (model: 18BW) to unused

channels in order to close the circuit.

•Azbil DCS AI connector

I/O cable: J-SSL / J-SSK

J-SRL / J-SRK

Location

Input connector: 00-8016-056-296-707V

CN1, CN2: J-HAM50 / J-HMM00 module use

The output 1 is connected to the connector. The CN1

and CN2 are connected in parallel.

18-RACK LOCATION NO.

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16

AZBIL DCS AI CONNECTOR

18-RACK LOCATION NO.

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16

AZBIL DCS AO CONNECTOR

I/O cable: J-SSL / J-SSK

J-SRL / J-SRK

Location

Output connector: 00-8016-056-296-707V

CN1, CN2: J-AOM10 module use

The input is connected to the connector. The CN1 and

CN2 are connected in parallel.

Install the Extender Module (model: 18BW) to unused

channels in order to close the circuit.

•Azbil DCS AO connector

Location

Output connector: HIF3CA-40PA-2.54DSA (11)

CN1, CN2: SAMP1

CN3, CN4: SAMP1 for redundancy

The output 1 is connected to the connector.

18-RACK LOCATION NO.

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

CN1, CN3

CN2, CN4

SAMP1 INPUT POINT NO.

•Toshiba DCS SAMP1 card use

Location

Input connector: HIF3CA-40PA-2.54DSA (11)

CN1, CN2: SAOP1

CN3, CN4: SAOP1 for redundancy

The input is connected to the connector.

18-RACK LOCATION NO.

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

CN1, CN3

CN2, CN4

SAOP1 OUTPUT POINT NO.

•Toshiba DCS SAOP1 card use

Location

Input connector: Omron XG4A-2031

The output 1 is connected to the connector.

18-RACK LOCATION NO.

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

CN1, CN2

CN3, CN4

SAIN1 INPUT POINT NO.

Toshiba DCS SAMP1 uses Panasonic AXM220001.

As connector is discontinued, Omron XG4A-2031 is

used as an alternative. (Replace cable side.)

CN1 : SAIN1 (ch.1 – ch.8)

CN2 : SAIN1 (ch.1 – ch.8) for redundancy

CN3 : SAIN1 (ch.9 – ch.16)

CN4 : SAIN1 (ch.9 – ch.16) for redundancy

•Toshiba DCS SAIN1 card use