MODEL: 47LPT

47LPT SPECIFICATIONS

ES-9506 Rev.14 Page 2/7

https://www.m-system.co.jp/

• Hysteresis (deadband)

• Moving average

• Others

(Refer to the instruction manual for details)

Read rate: 40 times/sec. (25 msec.)

Averaging: None or moving average

Lockout setting: Prohibiting certain operations; protecting

settings

DISPLAY

Display: 16 mm (.63) high, 4 ½ digits, 7-segment LED

Display range: -19999 to 19999

Zero indication: Higher-digit zeros are suppressed.

Over-range indication: ‘-19999’ or ‘19999’ blinking for

display values out of the scaled range.

‘S.ERR’ and ‘Max’ blinking when the input signal is out of

the usable range.

Alarm status indication

LL indicator: Green turns on when the LL alarm is tripped.

L indicator: Green turns on when the L alarm is tripped.

H indicator: Red turns on when the H alarm is tripped.

HH indicator: Red turns on when the HH alarm is tripped.

P indicator: Amber turns on when none of the other alarms

is tripped.

Note: Only ‘P’ turns on with no-alarm-output type. ‘LL’ or

‘HH’ does not turn on with dual-alarm-output type.

All setpoints can be independently set either for Hi or Lo

alarm trip.

Function indicators:

Zro, Spn, D/P, Tch, Fnc, Min, Max

Display mode status and operation status, amber ON or

blink

Engineering unit indication: Sticker label attached

DC, AC, mV, V, kV, μA, mA, A, kA, mW, W,

kW, var, kvar, Mvar, VA, Hz, Ω, kΩ, MΩ,

cm, mm, m, m/sec, mm/min, cm/min, m/min,

N, kN, Pa, kPa, MPa, t, t/h, ℃, °F, %RH, J,

INPUT SPECIFICATIONS

Frequency: 50 or 60 Hz

Overload capacity: 450 V for 10 sec., 360 V continuous

Default measuring range: 0 – 300 V

TYPE

MEASURING

OPERATIONAL

INPUT

IND

RANGE

RANGE

BURDEN

V150

0 – 150V

0 – 165V

≤0.5VA

V300

0 – 300V

0 – 330V

≤0.5VA

OUTPUT SPECIFICATIONS

■ DC Output

• DC Current

Operational range: -5 – +105 %

• DC Voltage

Operational range: -5 – +105 %

■ Alarm Output: Relay contact

Rated load: 250 V AC @ 3 A (cos ø = 1)

30 V DC @ 3 A (resistive load)

Maximum switching voltage: 250 V AC, 30 V DC

Maximum switching power: 750 VA, 90 W (resistive load)

Minimum load: 5 V DC @ 10 mA

INSTALLATION

Power consumption

•AC: Approx. 6.5VA

•DC: Approx. 3 W

Operating temperature: -10 to +55°C (14 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Panel flush mounting

Weight: 300 g (0.66 lb)

PERFORMANCE

Accuracy

Display: ±0.5 % ±10 digits with input 5 – 100 %

Output: ±0.1 %

(DC output = display + output)

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Input resolution: Max. 16 bits

Output resolution: Max. 14 bits

Response time: ≤ 0.5 sec.

(alarm output: 0 – 100 % at 90 % setpoint)

≤ 0.5 sec. (DC output: 0 – 90 %)

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @ 1 minute (input to DC

output to HH output or H output to L output or LL output to

power to ground)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1

Measurement Category III (input)

Measurement Category II (alarm output)

Installation Category II (power)

Pollution Degree 2