MCP4432 datasheet(16/94 Pages) MICROCHIP

16 / 94 page

MCP443X/5X

DS22267A-page 16

 2010 Microchip Technology Inc.

107

TSU:DAT Data input setup

time

100 kHz mode

250

—

Note 2

400 kHz mode

100

—

1.7 MHz mode

—

3.4 MHz mode

—

109

TAA

Output valid

from clock

100 kHz mode

—

3450

Note 1

400 kHz mode

—

900

1.7 MHz mode

—

150

Cb = 100 pF,

Note 1, Note 7

—

310

Cb = 400 pF,

Note 1, Note 5

3.4 MHz mode

—

150

Cb = 100 pF, Note 1

110

TBUF

Bus free time

100 kHz mode

4700

—

Time the bus must be free

before a new transmission

can start

400 kHz mode

1300

—

1.7 MHz mode

N.A.

—

3.4 MHz mode

N.A.

—

TSP

Input filter spike

suppression

(SDA and SCL)

100 kHz mode

—

NXP specification states

N.A.

400 kHz mode

—

1.7 MHz mode

—

Spike suppression

3.4 MHz mode

—

Spike suppression

TABLE 1-3:

I2C BUS DATA REQUIREMENTS (SLAVE MODE) (CONTINUED)

I2C AC Characteristics

Standard Operating Conditions (unless otherwise specified)

Operating Temperature

–40

C  TA  +125C (Extended)

Operating Voltage VDD range is described in AC/DC characteristics

Param.

No.

Sym

Characteristic

Min

Max

Units

Conditions

Note 1:

As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region

(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions.

A fast-mode (400 kHz) I2C-bus device can be used in a standard-mode (100 kHz) I2C-bus system, but the

requirement tSU;DAT  250 ns must then be met. This will automatically be the case if the device does not

stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal,

it must output the next data bit to the SDA line

TR max.+tSU;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I2C bus specification) before

the SCL line is released.

The MCP44X1/MCP44X2 device must provide a data hold time to bridge the undefined part between VIH

and VIL of the falling edge of the SCL signal. This specification is not a part of the I2C specification, but

must be tested in order to ensure that the output data will meet the setup and hold specifications for the

receiving device.

Use Cb in pF for the calculations.

Not Tested.

A Master Transmitter must provide a delay to ensure that difference between SDA and SCL fall times do

not unintentionally create a Start or Stop condition.

Ensured by the TAA 3.4 MHz specification test.

MCP4432 数据表(PDF) 16 Page - Microchip Technology

MCP4432 数据表(HTML) 16 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94

数据表下载

链接网址

MCP4432 数据表(PDF) 16 Page - Microchip Technology

MCP4432 数据表(HTML) 16 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94

数据表 下载

链接网址

数据表下载