Triple PLL Field Prog. Spread Spectrum Clock Synthesizer

MDS 290 C

3

Revision 062305

Integrated Circuit Systems, Inc.

ICS290

PRELIMINARY INFORMATION

External Components

The ICS290 requires a minimum number of external

components for proper operation.

Series Termination Resistor

Clock output traces over one inch should use series

termination. To series terminate a 50

Ω trace (a

commonly used trace impedance), place a 33

Ω resistor

in series with the clock line, as close to the clock output

pin as possible. The nominal impedance of the clock

output is 20

Ω.

Decoupling Capacitors

As with any high-performance mixed-signal IC, the

ICS290 must be isolated from system power supply

noise to perform optimally.

Decoupling capacitors of 0.01µF must be connected

between each VDD and the PCB ground plane. For

optimum device performance, the decoupling capacitor

should be mounted on the component side of the PCB.

Avoid the use of vias on the decoupling circuit.

Crystal Load Capacitors

The device crystal connections should include pads for

small capacitors from X1 to ground and from X2 to

ground. These capacitors are used to adjust the stray

capacitance of the board to match the nominally

required crystal load capacitance. Because load

capacitance can only be increased in this trimming

process, it is important to keep stray capacitance to a

minimum by using very short PCB traces (and no vias)

been the crystal and device. Crystal capacitors must be

connected from each of the pins X1 and X2 to ground.

The value (in pF) of these crystal caps should equal

capacitance in pF. Example: For a crystal with a 16 pF

load capacitance, each crystal capacitor would be 20

pF [(16-6) x 2] = 20.

ICS290 Configuration Capabilities

The architecture of the ICS290 allows the user to easily

configure the device to a wide range of output

frequencies, for a given input reference frequency.

The frequency multiplier PLL provides a high degree of

precision. The M/N values (the multiplier/divide values

available to generate the target VCO frequency) can be

set within the range of M = 1 to 1024 and N = 1 to

32,895.

The ICS290 also provides separate output divide

values, from 2 through 63, to allow the two output clock

banks to support widely differing frequency values from

the same PLL.

Each output frequency can be represented as:

Output Drive Control

The ICS290 has two output drive settings. Low drive

should be selected when outputs are less than 100

MHz. High drive should be selected when outputs are

greater than 100 MHz. (Consult the AC Electrical

Characteristics for output rise and fall times for each

drive option.)

ICS VersaClock Software

ICS applies years of PLL optimization experience into a

user friendly software that accepts the user’s target

reference clock and output frequencies and generates

the lowest jitter, lowest power configuration, with only a

press of a button. The user does not need to have prior

PLL experience or determine the optimal VCO

frequency to support multiple output frequencies.

VersaClock software quickly evaluates accessible VCO

frequencies with available output divide values and

provides an easy to understand, bar code rating for the

target output frequencies. The user may evaluate

output accuracy, performance trade-off scenarios in

seconds.

Spread Spectrum Modulation

The ICS290 utilizes frequency modulation (FM) to

distribute energy over a range of frequencies. By

modulating the output clock frequencies, the device

effectively lowers energy across a broader range of

frequencies; thus, lowering a system’s electromagnetic

interference (EMI). The modulation rate is the time from

transitioning from a minimum frequency to a maximum

frequency and then back to the minimum.

Spread Spectrum Modulation can be applied as either

“center spread” or “down spread”. During center spread

modulation, the deviation from the target frequency is

equal in the positive and negative directions. The

OutputFreq

REFFreq

M

N

-----

⋅

=