MODEL: R3-GFL1

R3-GFL1 SPECIFICATIONS

ES-8461 Rev.13 Page 2/6

https://www.m-system.co.jp/

Internal power: Via the Installation Base (model: R3-BSx)

RUN contact output: Euro type connector terminal

mm)

RUN/CFG selector: Toggle switch; RUN or Configuration

Isolation: Ethernet to internal bus or internal power to RUN

contact output

Indicator LEDs

RUN: Green LED turns on when the CPU, internal bus and

field bus on the other interface module are in normal

conditions.

ERR: Red LED turns on in an abnormality of the system.

LNK: Red LED turns on while the R3-GFL1 is participating

FL-net (normal communication)

HER: Red LED turns on in an abnormality of I/O data.

PER: Red LED blinks on with the parameter setting error.

CFG: Red LED blinks in high speed at the startup; blinks in

low speed while the builder software is used.

TX: Green LED turns on while transmitting.

RX: Amber LED turns on while receiving.

Module allocation: Set with the side DIP switch.

■ RUN CONTACT OUTPUT

RUN contact: Relay turns on when the CPU, the internal bus

function and the field bus on the other interface module are

in normal conditions.

Rated load: 250 V AC @0.5A (cos ø = 1)

30 V DC @ 0.5 A (resistive load)

(< 50 V AC, < 75 V DC for EU conformity)

Maximum switching voltage: 250 V AC or 220 V DC

Maximum switching power: 62.5 VA or 60 W

Minimum load: 10 mV DC @ 1 mA

When driving an inductive load, external contact protection

and noise quenching are recommended.

FL-net SPECIFICATIONS

FL-net: Ver.2.0 supported

Physical layer standard: IEEE 802.3u

Data link layer: 10BASE-T / 100BASE-TX

Baud rate: 10 / 100 Mbps, Auto Negotiation

Protocol: FL-net (OPCN-2) (UDP/IP)

Transmission media: 10BASE-T (STP cable, category 5)

100BASE-TX (STP cable, category 5e)

Max. segment length: 100 meters

Max. number of nodes: 254

IP address: FL-net Configuration Builder is used to set up the

IP address and the network address.

Factory setting:

192.168.250.1 (IP address)

255.255.255.0 (network address)

Max. cyclic data size:

8 k bits (area 1) + 8 k words (area 2) / system

4 k bits (area 1) + 256 words (area 2) / node

Max. message data size: 1024 bytes (per transmission

cycle)

Performance (2k bits + 2k words / node, 32 nodes in total)

Token cycle time: 50 milliseconds (1.56 milliseconds/ node

in average)

Message transmission time: 500 milliseconds (1 : 1

unidirectional message)

INSTALLATION

Current consumption: 150 mA

Operating temperature: -10 to +55°C (14 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: Installation Base (model: R3-BSx)

Weight: 200 g (0.44 lb)

PERFORMANCE

Data allocation: 16 × n (Module allocation: 1 to 8)

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 1500 V AC @ 1 minute

(Ethernet to internal bus or internal power to RUN contact

output)

2000 V AC @ 1 minute (power input to FG; isolated on the

power supply module)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

RoHS Directive